thermofin TCS.2 Series Скачать руководство пользователя страница 122

Страница: 122 / 162

Controller operating manual

15.11.2020 – Version 1.1

TCS.2 series –

thermofin

control system 2

generation

Page: 122/162

Operating manual - translation into English © thermofin GmbH

Editable from … to:

0 … 100 %

Factory setting:

80 %

Delay winter operation OFF:

Defines a delay in minutes in which both the temperature

(winter operation OFF >) and the “RPM Winter operation OFF”

must have exceeded the set changeover limit in order to

deactivate winter operation. This delay prevents winter

operation from being switched on and off continuously when

the changeover values are reached.

Editable from … to:

0 … 600 min

Factory setting:

10 min

Current status:

Winter or summer operation active

Allows switching between summer and winter operation using

the switch symbol. This function is intended for commissioning

and test purposes. If the ambient temperature falls below the

lower temperature limit, it is no longer possible to switch off

winter operation for safety reasons.

Display of ambient temperature

Currently measured ambient temperature. Useful for commissioning and adjusting the settings.

Display of main valves

Status display of the main valve positions. The following symbols are used as indicators in the

display:

Valve is OPEN

Valve is CLOSED

Valve is OPENING

Valve is CLOSING

Содержание TCS.2 Series



































































































































































Результаты поиска

Содержание TCS.2 Series

Отзывы:

Похожие инструкции для TCS.2 Series

Бренды по названию

Популярные бренды

thermofin TCS.2 Series, Руководство по эксплуатации

Результаты поиска

Содержание TCS.2 Series

Отзывы:

Похожие инструкции для TCS.2 Series

Бренды по названию

Популярные бренды