Thermo Scientific Thermo Scientific Vanquish VC-D40 Скачать руководство пользователя страница 107

Страница: 107 / 174

•

Maintenance and Service

Variable Wavelength Detectors (VC-D40, VF-D40)
Operating Manual

Page 107

7.5

Lamps

This section describes the replacement and installation of the

•

UV lamp (see

Replacing the UV Lamp (Deuterium Lamp)

•

Replacing the VIS Lamp (Tungsten Lamp)

(

}

page 110)

NOTICE—Damage to the device

Usage of lamps not supplied or approved by Thermo Fisher Scientific for
this detector may result in inferior performance, detector malfunction or
may damage the detector. Detector guaranty may be voided.

Use only lamps supplied or approved by Thermo Fisher Scientific for this
detector.

7.5.1

Replacing the UV Lamp (Deuterium Lamp)

When

•

The lamp is defective

•

After a defined amount of operating hours of the lamp as a
preventive measure

•

The lamp intensity is too low for demanding applications

•

The lamp intensity fluctuates causing artifacts in the baseline

Parts required

•

UV lamp

•

Optionally:

Isopropanol

Lint-free tissue

Preparations

1. Turn off the UV lamp.

2. Turn off the device.

Содержание Thermo Scientific Vanquish VC-D40















































































































































































Результаты поиска

Содержание Thermo Scientific Vanquish VC-D40

Отзывы:

Похожие инструкции для Thermo Scientific Vanquish VC-D40

Бренды по названию

Популярные бренды

Thermo Scientific Thermo Scientific Vanquish VC-D40, Руководство по эксплуатации

Результаты поиска

Содержание Thermo Scientific Vanquish VC-D40

Отзывы:

Похожие инструкции для Thermo Scientific Vanquish VC-D40

Бренды по названию

Популярные бренды