manualshive.com logo in svg

Thermo Scientific Surveyor UV Plus, Руководство по оборудованию

Поделиться
Скачать
Thermo Scientific Surveyor UV Plus Скачать руководство пользователя страница 70

A

  Surveyor Firmware Upgrade Utility

54

Surveyor UV/Vis Plus Detector Hardware Manual

Thermo Scientific

6. In the Surveyor Firmware Upgrade Utility window, initiate communication between the 

utility and the Surveyor UV/Vis Plus Detector as follows:

a. In the Device Type area, select the 

Surveyor UV/VIS 

option. See 

Figure 36

.

Figure 36. 

Surveyor Firmware Upgrade Utility, showing the Surveyor UV/Vis option 
selected

b. Click 

Connect

. 

The status display at the bottom of the Surveyor Firmware Upgrade Utility window 
indicates that a connection has been made. See 

Figure 37

.

CAUTION  

Do not interrupt the firmware download process. Do not turn off the 

power to the Surveyor UV/Vis Plus Detector or close the Surveyor Firmware 
Upgrade Utility while the detector is connected to the Surveyor Firmware 
Upgrade Utility. If you lose power to the detector during the firmware download 
process, contact your Thermo Fisher Scientific representative to reprogram the 
firmware board.

Содержание Surveyor UV Plus













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды