manualshive.com logo in svg

Thermo Scientific SRD-3200, Руководство по эксплуатации


Поделиться
Скачать
background image

UltiMate 3000 Series:  

SRD-3x00 Solvent Racks  

 

Operating Instructions  

Page 

i 

Table of Content 

1

 

Introduction ................................................................................................................... 1

 

1.1

 

How to Use this Manual ............................................................................................ 1

 

1.2

 

Safety Information ..................................................................................................... 2

 

1.2.1

 

Symbols on the Module and in the Manual ...................................................... 2

 

1.2.2

 

Safety Precautions ............................................................................................ 3

 

1.2.3

 

Consignes de Sécurité

 .................................................................................. 6

 

1.3

 

Intended Use .............................................................................................................. 9

 

1.4

 

Federal Communications Commission (FCC) Note ................................................ 10

 

2

 

Overview ...................................................................................................................... 11

 

2.1

 

Unit Description ....................................................................................................... 11

 

2.2

 

SRD Configurations ................................................................................................. 11

 

2.3

 

Front Panel Elements ............................................................................................... 13

 

2.4

 

Rear Panel ................................................................................................................ 14

 

2.5

 

Fluid Connections .................................................................................................... 15

 

2.6

 

Leak Sensor .............................................................................................................. 16

 

2.7

 

Wellness ................................................................................................................... 16

 

3

 

Installation ................................................................................................................... 17

 

3.1

 

Facility Requirements .............................................................................................. 17

 

3.2

 

Unpacking ................................................................................................................ 17

 

3.3

 

Positioning the SRD in the UltiMate 3000 System ................................................. 19

 

3.4

 

Connecting the SRD ................................................................................................ 21

 

3.4.1

 

Connecting the SRD to an UltiMate 3000 System Pump ............................... 21

 

3.4.2

 

Connecting the SRD to the Main Power Supply (Optional) .......................... 21

 

4

 

Preparation for Operation (Startup) ........................................................................ 23

 

4.1

 

Overview .................................................................................................................. 23

 

4.2

 

Connecting Drain Tubing ........................................................................................ 23

 

4.3

 

Solvent Reservoirs ................................................................................................... 24

 

4.3.1

 

General Notes ................................................................................................. 24

 

4.3.2

 

Connecting the Solvent Reservoirs ................................................................ 25

 

4.3.3

 

Connecting the Solvent Supply Lines to the Degasser ................................... 27

 

5

 

Operation and Maintenance ...................................................................................... 29

 

5.1

 

Choosing the Solvents ............................................................................................. 29

 

5.2

 

General Notes for Degasser Operation .................................................................... 31

 

5.3

 

Operational Settings ................................................................................................. 32

 

5.3.1

 

Turning the Degasser on or off (from the UltiMate 3000 System Pump) ...... 32

 

5.3.1.1

 

Turning the Degasser on and off from the Pump Display ....................... 32

 

5.3.1.2

 

Turning the Degasser on and off in Chromeleon .................................... 33

 

5.3.2

 

Turning the Degasser On or Off (Stand-alone Operation) ............................. 34

 

Содержание SRD-3200

































































Отзывы:

Нет отзывов

Похожие инструкции для SRD-3200

ABB FIO-01 Quick Manual preview
FIO-01
Бренд: ABB Страницы: 14
ICS ELECTRONICS 4803 Quick Start Manual preview
4803
Бренд: ICS ELECTRONICS Страницы: 6
Danelec DM800 Installation Manual preview
DM800
Бренд: Danelec Страницы: 67
Garmin PORTABLE ICE FISHING KIT Installation Instructions preview
PORTABLE ICE FISHING KIT
Бренд: Garmin Страницы: 5
Taurus HS 100 Assembly Instructions Manual preview
HS 100
Бренд: Taurus Страницы: 24
jablotron UC-280 Instructions preview
UC-280
Бренд: jablotron Страницы: 2
Nabtesco Symphony NK-6 User Manual preview
Symphony NK-6
Бренд: Nabtesco Страницы: 26
Yuwell 7E-B5 Operation Instructions preview
7E-B5
Бренд: Yuwell Страницы: 2
MAGSTIM NEUROSIGN V4 User Manual preview
NEUROSIGN V4
Бренд: MAGSTIM Страницы: 86
ZAMST EK-1 Instructions For Use Manual preview
EK-1
Бренд: ZAMST Страницы: 14
Future Artist MIDI LOOPER Manual preview
MIDI LOOPER
Бренд: Future Artist Страницы: 42
Jenx GAMMA GA1 Instructions For Use Manual preview
GAMMA GA1
Бренд: Jenx Страницы: 34
Lightolier F7000-19 Specification Sheet preview
F7000-19
Бренд: Lightolier Страницы: 2
Metrohm OMNIS 2.1006.0010 Product Manual preview
OMNIS 2.1006.0010
Бренд: Metrohm Страницы: 34
Karma LED PAR9030 Instruction Manual preview
LED PAR9030
Бренд: Karma Страницы: 12
Blackrock Microsystems NeuroPort Instructions For Use Manual preview
NeuroPort
Бренд: Blackrock Microsystems Страницы: 74
Kleinwaechter WST 50 Manual preview
WST 50
Бренд: Kleinwaechter Страницы: 8
Leister WELDPLAST 200-i Operating Instructions Manual preview
WELDPLAST 200-i
Бренд: Leister Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды