Thermo Scientific Sorvall LYNX 4000 Скачать руководство пользователя страница 27

Страница: 27 / 72

Before Use

Shipping the Centrifuge

Thermo Scientific

Sorvall LYNX 4000 / 6000

Shipping the Centrifuge

Before shipping the centrifuge please bear the following in mind:

•

The centrifuge must be cleaned and decontaminated.

•

The decontamination must be confirmed in a special form.

Transporting the Centrifuge

•

Use a forklift to lift the centrifuge.

•

The centrifuge can be damaged by impact.

•

Transport the centrifuge upright and if at all possible in packaging.

WARNING

Before shipping or deposing centrifuges and accessories you have to clean and

if necessary disinfect or decontaminate the entire system.

Note

Store the centrifuge packaging. Contact a shipping company for the transport. Inform

customer service.

Always remove the rotor before moving the centrifuge. If you do not remove the rotor you might
damage the centrifuge drive or centrifuge spindle.

Содержание Sorvall LYNX 4000









































































Результаты поиска

Содержание Sorvall LYNX 4000

Отзывы:

Похожие инструкции для Sorvall LYNX 4000

Бренды по названию

Популярные бренды

Thermo Scientific Sorvall LYNX 4000, Инструкция по эксплуатации

Результаты поиска

Содержание Sorvall LYNX 4000

Отзывы:

Похожие инструкции для Sorvall LYNX 4000

Бренды по названию

Популярные бренды