Thermo Scientific Sorvall LYNX 4000 Скачать руководство пользователя страница 17

Страница: 17 / 72

Introduction and Description

Rotor Selection

Thermo Scientific

Sorvall LYNX 4000 / 6000

Rotor Selection

The Sorvall LYNX 4000 / 6000 centrifuge is supplied without a rotor.

Various Thermo Scientific rotors are available to choose from.

The technical data of the rotors and the corresponding adapters and reduction sleeves for various
commercially available containers can be found in the corresponding rotor operating manuals.

For more information visit our website at

www.thermo

fisher

.com/rotors

BIOFlex HC

75003000

BIOFlex HS

75003002

TH13-6x50

75003010

F9-6x1000 LEX

096-061075

F10-4x1000 LEX

096-041075

F12-6x500 LEX

096-062375

F14-6x250y

096-062075

F14-14x50cy

096-145075

F20-12x50 LEX

096-124375

F21-8x50y

096-084275

F23-48x1.5

096-484075

TCF-20 Zonal

75003013

TCF-20

75003012

T29-8x50

75003009

A27-8x50

75003008

A27-6x50

75003007

A22-24x16

75003005

A21-24x15c

75003004

A23-6x100

75003006

Содержание Sorvall LYNX 4000









































































Результаты поиска

Содержание Sorvall LYNX 4000

Отзывы:

Похожие инструкции для Sorvall LYNX 4000

Бренды по названию

Популярные бренды

Thermo Scientific Sorvall LYNX 4000, Инструкция по эксплуатации

Результаты поиска

Содержание Sorvall LYNX 4000

Отзывы:

Похожие инструкции для Sorvall LYNX 4000

Бренды по названию

Популярные бренды