Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя

Страница: 90 / 148

Absorbance Ratio

Setting Up Test Parameters

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

2. Highlight the test to recall and press

Enter

This screen provides these capabilities:

•

Setting Up Test Parameters

•

Cell Correction

•

Saving a Test

• Viewing the list of stored tests

•

Measuring a Blank

Setting Up Test Parameters



To set up test parameters

1. In the Absorbance Ratio screen, highlight the desired parameter.

2. When the parameters are set, press

Save Test

to save the test or

Run Test

to measure a

blank or samples.

Measuring Samples

Note

If Cell Correction is ON, you must run the Setup Correction application before

you can access Run Test or Measure Samples.

Note

If Auto Save Data is ON, you must enter a Data File Name before you can

access Run Test or Measure Samples.

Содержание Orion AquaMate 7000 Vis





















































































































































Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя

Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды