manualshive.com logo in svg

Thermo Scientific MaxQ 3000, Руководство по эксплуатации

Поделиться
Скачать
Thermo Scientific MaxQ 3000 Скачать руководство пользователя страница 12

MaxQ 3000 Shaker

2-3

Thermo Scientific

Section 2

General Specifications

Environmental

Conditions

The Thermo Scientific MaxQ 3000 Series bench top, orbital, open-air
shakers are available in one of two control configurations:

•    SHKA3000 and SHKA3000-1CE incorporate a mechanical timer for

the control of time and speed, adjustable with rotary dials. Analog
tachometer displays speed in RPM, verifying accuracy of speed setting.

•    SHKE3000 and SHKE3000-1CE control time and speed by a

microprocessor controller, adjustable with arrow keys on keypad in one
rpm increments. Flashing display indicates power interruption.
Pressing any key will clear display. Non-volatile memory maintains
speed and time set points in the event of a power interruption. Speed
and time set points are automatically reactivated after power is
restored. User adjustable speed calibration allows end user to calibrate
the shaking speed to a known value.

In addition, both versions offer:

•    1 inch (2.54 cm) triple eccentric orbital drive

•    6 permanently lubricated ball bearings

•    50 lb (22.7 kg) platform load capacity at safe speeds less than 400 rpm

for SHKA3000/SHKA3000-1CE and less than 500 rpm for
SHKE3000/SHKE3000-1CE

Pollution Degree**   . . . . . . . . . . . . . . . . . . . . . . . . .2
Installation Category**  . . . . . . . . . . . . . . . . . . . . . .II
Altitude  . . . . . . . . . . . . . . . 3000 meters MSL (Mean Sea Level)
Relative Humidity . . . . 20% to 80% maximum, non-condensing
Electrical Supply   . . . . . . . . . .120 VAC or 240 VAC
Voltage Tolerance   . . . . . .+10% of normal rated line
Temperature   . . . . . . . . . . . . . . . . . . . . .0°C to 40°C
Product Usage  . . . . . . This product is intended for use indoors only

**Refer to IEC 664-1

Caution

It’s not recommended to operate shaker in a CO2 enriched

atmosphere. Formation of carbonic acid could cause electrical failures. 

s

Declaration of Conformity available on request.

Содержание MaxQ 3000



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды