Thermo Scientific ISQ 7000 Скачать руководство пользователя | Manualshive

Страница: 44 / 442

background image

1

Performing Routine Maintenance

Replacing a Column

16

ISQ 7000 Hardware Manual

Thermo Scientific

Replacing a Column



To replace a column

1. Cool down the GC oven and injector. See the GC documentation for information.

The procedure for replacing a column depends on your system configuration. If your system
does not have a VPI or has an AEI ion source installed, see

“Replacing a column in a ISQ

7000 system with no VPI or an AEI ion source”

. If your ISQ 7000 MS has a

vacuum probe interlock (VPI) and the ExtractaBrite ion source is installed, see

column on a ISQ 7000 system with a VPI and an ExtractaBrite ion source”

.

Replacing a column in a ISQ 7000 system with no VPI or an AEI ion source

If your ISQ 7000 system has no VPI or has an AEI ion source installed on the system, follow
the instructions below to replace the column.



To replace the factory-installed column in the ISQ 7000 system in a system with no
VPI or with an AEI ion source installed

1. Cool down the GC oven and injector. See the GC documentation for information.

2. Open the ISQ 7000 Dashboard and click

Shut Down

.

During the shutdown procedure the vacuum and heaters lights will remain off. Once the
procedure is complete and the instrument is ready to be powered off, the power light will
turn amber and start blinking rapidly. At this point it is safe to power off the ISQ 7000
system.

Note

If you are running samples, stop the acquisition before powering off the system.

WARNING BURN HAZARD:

The injector, oven, and transfer line may be hot. Allow them

to cool to room temperature before touching them.

ATTENTION RISQUE DE BRÛLURE :

l’injecteur, les détecteurs, le four et la ligne de transfert

peuvent être chauds. Laissez-les refroidir avant de les toucher.

Note

Some of the cleaning procedures in this section require the use of methanol. If

methanol is unavailable or prohibited, substitute LCMS-grade or GC-grade ethanol or
isopropyl alcohol. Do not use denatured ethanol as it may contain impurities that
contaminate the GC-MS system.

Note

If you are running samples, stop the acquisition before powering off the system.

«
...
42
43
44
45
46
...
»

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

Бренд: Major tech Страницы: 8

Бренд: Waltron Страницы: 25

Бренд: dbx Страницы: 2

Бренд: E Instruments Страницы: 2

Бренд: JRC Страницы: 308

Smart Probes 115i

Бренд: TESTO Страницы: 17

Бренд: BizLine Страницы: 62

Бренд: DriveTest Страницы: 24

Бренд: Mannix Страницы: 5

OPTIFLUX 4040 C Series

Бренд: KROHNE Страницы: 20

Бренд: Lutron Electronics Страницы: 20

Бренд: Rion Страницы: 4

Бренд: Fluidwell Страницы: 48

Бренд: PICO Страницы: 2

Combo meter P700 Pro

Бренд: AquaMaster Страницы: 20

Бренд: Magnescale Страницы: 2

Бренд: Keithley Страницы: 338

Бренд: T&D Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды