Thermo Scientific ISQ 7000 Скачать руководство пользователя

Страница: 403 / 442

Upgrade Equipment

Advanced EI Ion Source

Thermo Scientific

ISQ 7000 Hardware Manual

375

5. Twist and remove the tray alignment pins that hold the magnet yoke to the back of the

manifold door. The magnet yoke will pull free of the door, releasing the alignment collar.

6. Set the old parts on a clean surface temporarily. There is a place to store them in the

Advanced EI source kit.

7. Remove the new source magnets and magnet yoke from the Advanced EI source kit and

put them together as shown in

Figure 425

Figure 425.

Assembling the Advanced EI Source Magnets and Yoke

8. Attach the source magnets and yoke to the manifold door using the new tray alignment

pins in the Advanced EI source kit. See

Figure 426

Figure 424.

Removing the Tray Alignment Pins and Bracket

Magnet Yoke

Tray Alignment
Pins

Magnet Yoke

Advanced EI
Source
Magnets

Содержание ISQ 7000



























































































































































































































































































































































































































































Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды

Thermo Scientific ISQ 7000, Руководство по оборудованию

Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды