Thermo Scientific ISQ 7000 Скачать руководство пользователя

Страница: 38 / 442

Performing Routine Maintenance

Powering On the ISQ 7000 Mass Spectrometer

ISQ 7000 Hardware Manual

Thermo Scientific

5. Check the lights on the front of the instrument to make sure it is ready for use.

•

Power

—If the Power light is a solid green, the instrument is powered on. When the

light is not lit, the instrument is not powered on.

Figure 2.

Powering On the ISQ 7000 Mass Spectrometer

Figure 3.

Using the Lights on the ISQ 7000 Mass Spectrometer

Power Switch

Vent Valve
Knob

Power

Vacuum

Busy

Heaters

Содержание ISQ 7000



























































































































































































































































































































































































































































Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды

Thermo Scientific ISQ 7000, Руководство по оборудованию

Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды