Thermo Scientific ISQ 7000 Скачать руководство пользователя

Страница: 364 / 442

Advanced Maintenance

Replacing the Boards in the ISQ 7000 Mass Spectrometer

336

ISQ 7000 Hardware Manual

Thermo Scientific

Electrometer Board Cable



To replace the electrometer board (15-pin male/female RS-232) cable

1. Shut down your system by following the steps in

“Shutting Down the ISQ 7000 System”

page 149

2. Use a T20 Torxhead screwdriver to loosen the top cover panel screw from the interior

front panel. Then slide the top cover panel toward the back of the instrument and lift it
off.

3. Use a T20 Torxhead screwdriver to remove the two screws holding the support bracket to

the middle of the instrument.

Note

See the

ISQ and TSQ GC-MS Spare Parts Guide

for information about ordering this

component.

Note

You do not have to remove the ion source cartridge or the column or vent the

instrument. If you are using hydrogen as a carrier gas, power off the GC.

Figure 371.

Removing the Controller Interface Board

Support Bracket

Dynode/Multiplier
Power Supply

Support Bracket

Содержание ISQ 7000



























































































































































































































































































































































































































































Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды

Thermo Scientific ISQ 7000, Руководство по оборудованию

Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды