Thermo Scientific ISQ 7000 Скачать руководство пользователя

Страница: 362 / 442

Advanced Maintenance

Replacing the Boards in the ISQ 7000 Mass Spectrometer

334

ISQ 7000 Hardware Manual

Thermo Scientific

Source Interface Board and Heat Shield



To replace the source interface board and heat shield

1. Shut down your system by following the steps in

“Shutting Down the ISQ 7000 System”

page 149

2. If you are only replacing the heat shield, you do not have to remove the analyzer tray.

Disconnect the filament board and wires from the source interface board and the left
screw to remove the heat shield.

3. Replace the heat shield and reattach the left screw.

4. Reconnect the filament board and wires to the source interface board.

5. If you must replace the source interface board, remove the analyzer tray from the

instrument by following the instructions in

“Removing the Analyzer Tray from the ISQ

7000 Instrument”

page 151

Note

See the

ISQ and TSQ GC-MS Spare Parts Guide

for information about ordering

these components.

Figure 369.

Replacing the Heat Shield the Filament Board Wires

Note

Keep all manifold parts you remove covered on a clean work surface so they will not

accumulate dust.

Source Interface
Board

Heat Shield

Left
Screw

Filament Board
and Wires

Right
Screw

Содержание ISQ 7000



























































































































































































































































































































































































































































Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды

Thermo Scientific ISQ 7000, Руководство по оборудованию

Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды