Thermo Scientific ISQ 7000 Скачать руководство пользователя

Страница: 296 / 442

Advanced Maintenance

Replacing Components of the Electron Multiplier

268

ISQ 7000 Hardware Manual

Thermo Scientific

9. Remove and replace the anode feedthrough, o-ring, standoff and screws.

10. Insert one screw and tighten it until it is snug. Then insert and tighten the other screw.

Once both screws fit snugly, retighten them.

11. Reattach the electrometer board and the four screws that hold it in place.

12. Reattach the electrometer shield and the four screws.

13. Reconnect the electrometer board cable.

14. Reattach the top cover panel and tighten the screw.

15. Restart your system by following the instructions in

“Restarting the System”

page 165

Figure 285.

Replacing the Anode Feedthrough, O-ring, Standoff and Screws

Note

Be sure to attach the standoff at the location shown in the above figure.

Anode Feedthrough
and O-ring

Standoff

Screws

Содержание ISQ 7000



























































































































































































































































































































































































































































Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды

Thermo Scientific ISQ 7000, Руководство по оборудованию

Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды