manualshive.com logo in svg

Thermo Scientific ISQ 7000, Руководство по оборудованию


Поделиться
Скачать
background image

Preface

Hydrogen Safety Precautions

Thermo Scientific

ISQ 7000 Hardware Manual

xix

Hydrogen Safety Precautions

Hydrogen is a colorless, odorless, highly flammable gas with the molecular formula H

2

. 

Hydrogen gas presents a hazard as it is combustible over a wide range of concentrations: at 
ambient temperature and pressure, this ranges from about 4% to 74.2% by volume. 

Hydrogen has a flash point of - 423 °F (- 253 °C) and an auto-ignition temperature of 
1,040 °F (560 °C). It has a very low ignition energy and the highest burning velocity of any 
gas. If hydrogen is allowed to expand rapidly from high pressure, it can self-ignite. Hydrogen 
burns with a flame that can be invisible in bright light. 

Before you begin using hydrogen, you should conduct a risk assessment based on the quantity 
of hydrogen to be used and the conditions of your laboratory. You should ask yourself:

“What hydrogen hazards associated with this project are most likely to occur?”

RISQUE DE SUBSTANCES TOXIQUES

:  indique que l’exposition à une 

substance toxique peut survenir et que l’exposition peut ou pourrait 
entraîner des blessures personnelles ou la mort.

Pour prévenir les blessures personnelles, ce symbole général d’avertissement 
précède le mot 

AVERTISSEMENT

 et est conforme à la norme ISO 3864-2. 

Dans le vocabulaire des signes ANSI Z535, ce symbole indique un risque de 
blessures personnelles si l’instrument est utilisé de manière inappropriée ou 
en cas d’actions dangereuses. Ce symbole et un autre symbole de sécurité 
approprié vous avertissent d’un risque imminent ou potentiel pouvant 
entraîner des blessures personnelles.

Symbol

Descriptor

WARNING  FIRE HAZARD:  

The use of hydrogen as a carrier gas is dangerous. Hydrogen is 

potentially explosive and must be used with extreme care. Any use of hydrogen gas must 
be reviewed by appropriate health and safety staff and all installations of hydrogen systems 
must be performed to applicable codes and standards. Thermo Fisher Scientific assumes 
no liability for the improper use of hydrogen as a carrier gas.

AVERTISSEMENT RISQUE D’INCENDIE

:  l’utilisation d’hydrogène comme gaz vecteur 

est dangereuse. L’hydrogène est potentiellement explosif et doit être utilisé avec une 
extrême précaution. Toute utilisation d’hydrogène gazeux doit être évaluée par le 
personnel de santé et de sécurité approprié et toutes les installations de systèmes 
d’hydrogène doivent se conformer aux codes et aux normes en vigueur. Thermo Fisher 
Scientific décline toute responsabilité en cas d’utilisation inappropriée d’hydrogène 
comme gaz vecteur.

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

X-Rite 891 Operation Manual preview
891
Бренд: X-Rite Страницы: 80
Felix Instruments F-940 Operation Manual preview
F-940
Бренд: Felix Instruments Страницы: 102
Oakton 150 Series Operating Instructions preview
150 Series
Бренд: Oakton Страницы: 4
IFR COM-120B Evaluation Manual preview
COM-120B
Бренд: IFR Страницы: 46
UEi C163 Quick Start Manual preview
C163
Бренд: UEi Страницы: 8
Unitech UT-1405 Instruction Manual preview
UT-1405
Бренд: Unitech Страницы: 18
Vectronics PM-30 Quick Manual preview
PM-30
Бренд: Vectronics Страницы: 4
Grundfos Vortex Flow Industry Instructions Manual preview
Vortex Flow Industry
Бренд: Grundfos Страницы: 16
Spacelabs 91390 Operation Manual preview
91390
Бренд: Spacelabs Страницы: 156
Hanna Instruments HI 84430 Instruction Manual preview
HI 84430
Бренд: Hanna Instruments Страницы: 25
VCA sound SMART RLT Sport User Manual preview
sound SMART RLT Sport
Бренд: VCA Страницы: 36
Wacom SD-310E User Manual preview
SD-310E
Бренд: Wacom Страницы: 23
Banner LAT-1 Quick Start Manual preview
LAT-1
Бренд: Banner Страницы: 4
Hanna Instruments HI 9023C Instruction Manual preview
HI 9023C
Бренд: Hanna Instruments Страницы: 21
Oakton Acorn TEMP 4 Operating Instructions Manual preview
Acorn TEMP 4
Бренд: Oakton Страницы: 8
PCE Americas PCE-428 User Manual preview
PCE-428
Бренд: PCE Americas Страницы: 111
SBS SBS-3500 Instruction Manual preview
SBS-3500
Бренд: SBS Страницы: 59
ZyAura ZGkb201p Operating Instructions preview
ZGkb201p
Бренд: ZyAura Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды