manualshive.com logo in svg

Thermo Scientific ISQ 7000, Руководство по оборудованию


Поделиться
Скачать
background image

2

 Troubleshooting

Investigating Filament and Lens Control Issues

128

ISQ 7000 Hardware Manual

Thermo Scientific

Investigating Filament and Lens Control Issues

Filament Check and Lens Check diagnostics can test the filament and lenses of the ISQ 7000 
system. Handle the lenses with care. Damaged lenses may cause short circuits, which prevent 
the lens supplies from functioning properly. 

Filament has burned out.

Filament does not last long.

Diagnostics indicate there is a problem with lens voltages.

WARNING  ELECTRICAL SHOCK HAZARD: 

 When troubleshooting any issue that requires 

removing a cover on the ISQ 7000 mass spectrometer, you should power-off and vent the 
instrument to avoid harming yourself.

AVERTISSEMENT RISQUE D’ÉLECTROCUTION

:  lorsque vous cherchez à résoudre un 

problème nécessitant d’enlever le couvercle du spectromètre de masse ISQ 7000, mettez 
hors tension et ventilez l’instrument pour éviter de vous blesser.

Possible Remedies

Make sure the lens driver board is connected to its bracket. See 

Lens Driver Board

 for details.

Locate and fix all air leaks into the carrier lines or vacuum manifold.

Make sure the filament wires are still connected to the source interface board. See 

Replacing a Dual Filament

 for details.

Run a Filament Check diagnostic to narrow down the source of the problem. Then replace the filament, as described in 

Replacing a Dual 

Filament

. 

Possible Remedies

Run a Leak Check diagnostic to check the system for air leaks and then address them. Use the Tetrafluoethane gas to find the leak.

Reduce the emission current in the instrument method.

Increase the time for your first scan until after the solvent peak has passed.

Possible Remedies

Make sure the lens driver board is attached to the bracket. If the board isn’t fully connected to the 20-pin feedthrough, you may get odd 
results. See 

Lens Driver Board

 for details.

Make sure all lens wires are clear of metal parts and the magnet yoke. Even though the wires are insulated with glass braid, electrical 
shorts may still be possible if the wires are touching metal.

Make sure the lenses are properly aligned in the ion cartridge sleeve.

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

Yamaha Clavinova CVP-601 Reference Manual preview
Clavinova CVP-601
Бренд: Yamaha Страницы: 98
Yamaha Electone CSY-1 Manual preview
Electone CSY-1
Бренд: Yamaha Страницы: 28
ILX Lightwave OMM-6810B User Manual preview
OMM-6810B
Бренд: ILX Lightwave Страницы: 126
UFM CoolPoint CP12-V8 Installation And Operation Manual preview
CoolPoint CP12-V8
Бренд: UFM Страницы: 14
TDI Nitro-Save NS16 Operating Instructions preview
Nitro-Save NS16
Бренд: TDI Страницы: 4
Environmental Express 99561-84 Instruction Manual preview
99561-84
Бренд: Environmental Express Страницы: 40
Det-Tronics 95-8632 Instructions Manual preview
95-8632
Бренд: Det-Tronics Страницы: 18
HBM T10F Mounting Instructions preview
T10F
Бренд: HBM Страницы: 84
H.E. Anderson Ratio:Guard Advanced Manual preview
Ratio:Guard Advanced
Бренд: H.E. Anderson Страницы: 9
Halcyon Multifunction Compensator Owner'S Manual preview
Multifunction Compensator
Бренд: Halcyon Страницы: 20
Sierra C100L-L-DD-LE-5-OV1-SV1-PV1C-V1-S1 Instruction Manual preview
C100L-L-DD-LE-5-OV1-SV1-PV1C-V1-S1
Бренд: Sierra Страницы: 55
NARDA AMB-8059 Quick Step Manual preview
AMB-8059
Бренд: NARDA Страницы: 60
doble TDR900 User preview
TDR900
Бренд: doble Страницы: 78
EKF Quo-Test User Manual preview
Quo-Test
Бренд: EKF Страницы: 32
Hioki 8730-10 Instruction Manual preview
8730-10
Бренд: Hioki Страницы: 288
UNI-T UT-P31 Instruction Manual preview
UT-P31
Бренд: UNI-T Страницы: 11
GARO GNM3T-RS485 Installation And Programming Manual preview
GNM3T-RS485
Бренд: GARO Страницы: 15
Mountz 070810 Operating Instructions Manual preview
070810
Бренд: Mountz Страницы: 27

Бренды по названию

Популярные бренды

Загрузить еще бренды