Thermo Scientific ISQ 7000 Скачать руководство пользователя | Manualshive

Страница: 152 / 442

background image

2

Troubleshooting

Investigating Communication Issues

124

ISQ 7000 Hardware Manual

Thermo Scientific

Sample data are not acquired.

GC is not communicating with the PC.

Autosampler is not communicating with the PC.

Possible Remedies

Make sure the autosampler methods and configuration include starting up and injecting a sample. You should also make sure the sample
has been injected.

Heated zone setpoint is not attained. See

Investigating Temperature Issues

for troubleshooting.

Verify that the ISQ 7000 system’s start mode is set properly.

Make sure the Remote Start cable is properly connected to the GC.

Make sure the End Run Time is set properly in the

ISQ 7000 Instrument Setup

file.

Add more disk space to the computer by backing up and removing files.

Possible Remedies

Make sure the GC is powered on.

Open the

Instrument Configuration

utility and make sure the GC is properly configured.

Make sure the cable between the computer and the GC is properly connected.

Verify the Communication port is properly configured on the computer.

Power-off the GC and power it back on again.

Possible Remedies

Make sure the autosampler is powered on.

Open the

Instrument Configuration

utility and make sure the autosampler is properly configured.

Make sure the cable between the GC and autosampler is properly connected.

«
...
150
151
152
153
154
...
»

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

Бренд: Idexx Страницы: 6

Бренд: IDEAL INDUSTRIES Страницы: 10

Бренд: M-system Страницы: 5

Бренд: OHAUS Страницы: 2

Бренд: JRC Страницы: 308

Бренд: Fluke Biomedical Страницы: 28

Бренд: VOLTCRAFT Страницы: 108

Бренд: Wetekom Страницы: 22

HydroTracer FLV

Бренд: aboni Страницы: 48

Бренд: E+E Elektronik Страницы: 20

Бренд: Brooks Страницы: 64

Бренд: brena Страницы: 26

Бренд: AKCP Страницы: 16

Бренд: Swann Страницы: 106

Бренд: LaserLiner Страницы: 64

Бренд: Konica Minolta Страницы: 92

Бренд: HANLA Страницы: 12

Бренд: Vaisala Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды