Thermo Scientific ISQ 7000 Скачать руководство пользователя | Manualshive

Страница: 119 / 442

background image

1

Performing Routine Maintenance

Replacing a Dual Filament

Thermo Scientific

ISQ 7000 Hardware Manual

91

Replacing a Dual Filament

The number of ions produced in the ion source is proportional to the filament emission
current. If the measured emission current is erratic, substantially less than the set emission
current value, or if the measured emission current is decreasing, you may need to replace the
dual filament because it has failed or is failing. Also, if one of the filaments has burned out, it
may be time to replace it.

You can increase the life of your dual filament by:

• Setting the solvent delay so that the analyzer will not turn on while the solvent peak is

eluting.

• Not overriding the solvent delay at the beginning of a run.

• Selecting a lower emission current.

• Ensuring the system is leak tight. The diagnostic leak test should be less than 7%. See

Investigating Vacuum Issues

for more information.

• Turning off the filament when changing the filament parameters in the software.



To replace the dual filament

1. Cool down the GC oven.

2. If you are using hydrogen as a carrier gas, cool down the injector to prepare the GC for

powering off. See the GC documentation for more information. After the heated zones
are cooled down, power-off the GC.

Note

See the

ISQ and TSQ GC-MS Spare Parts Guide

for information about ordering a

new filament.

Note

Click the

Instrument Control

button in the Xcalibur Status panel to switch

between filaments A and B.

WARNING BURN HAZARD:

The injector, oven, and transfer line may be hot. Allow them

to cool to room temperature before touching them.

AVERTISSEMENT RISQUE DE BRÛLURE

: l’injecteur, le four et la ligne de transfert

peuvent être chauds. Laissez-les refroidir à la température ambiante avant de les toucher.

WARNING FIRE HAZARD:

If you are using hydrogen as a carrier gas, you must cool down

and shut off the GC to prevent the buildup of hydrogen in the vacuum manifold. See the

“Hydrogen Safety Precautions”

of the Preface for more information.

«
...
117
118
119
120
121
...
»

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

Бренд: ABB Страницы: 8

Бренд: Labom Страницы: 5

Бренд: Kawai Страницы: 8

Бренд: ELGO Electronic Страницы: 24

OPERA CONTROL CENTER SERVER - V 3.5

Бренд: OPTICOM Страницы: 21

Бренд: SIGLENT Страницы: 32

Бренд: Interacoustics Страницы: 54

Бренд: PCB Piezotronics Страницы: 10

Ratio:Guard Advanced

Бренд: H.E. Anderson Страницы: 9

Бренд: Proteus Страницы: 4

Бренд: LaserLiner Страницы: 84

Бренд: Agilent Technologies Страницы: 26

Бренд: GE Страницы: 16

Бренд: Fluke Страницы: 2

Бренд: horiba Страницы: 103

Pianovelle GRP3

Бренд: Baldwin Страницы: 34

Бренд: TE Connectivity Страницы: 5

Бренд: Radiation Alert Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды