Thermo Scientific Ion Torrent A45727 Скачать руководство пользователя страница 74

Страница: 74 / 163

Note:

It is not necessary to resuspend the magnetic beads completely—it is only

necessary to dislodge most of the beads that may be trapped in the keyhole.

The instrument resuspends the beads during the run when needed.

Fine bubbles can form above the liquid in some tubes after inversion. These

bubbles do not affect the run.

Inspect all strips for large bubbles lodged under the surface of the liquid in the

tubes. Gently tap the strips on a benchtop to dislodge any bubbles without

splashing the contents onto the upper tube walls. If tapping fails to dislodge a

bubble, use the technique that is described in substep 4b until large bubbles are

dislodged.

Fill Genexus

™

Primer Pool Tubes

(custom assays only)

If you are using a custom assay, Genexus

™

Primer Pool Tubes must be manually filled

with the custom Ion AmpliSeq

™

or Ion AmpliSeq

™

HD panels at the appropriate

volume and in the correct primer pool tube positions. For Ion AmpliSeq

™

library

panels, use one carrier per DNA or RNA primer pool. The two positions in the primer

pool tube carrier are designated as shown in the following figure:

Position 1 tube: Contains Ion AmpliSeq

™

DNA, Ion AmpliSeq

™

RNA, or Ion AmpliSeq

™

FWD primer pool

Position 2 tube: Contains Ion AmpliSeq

™

HD REV primer pool

Add primer pool at the indicated volume to Genexus

™

Primer Pool Tubes using

the following table as a guide.

Primer pool type

Concentration

Volume in

position 1

Volume in

position 2

Ion AmpliSeq

™

DNA

100 nM

140 µL

—

Ion AmpliSeq

™

RNA

250 nM

70 µL

—

Ion AmpliSeq

™

HD FWD

Depends on plexy

55 µL

—

Ion AmpliSeq

™

HD REV

Depends on plexy

—

55 µL

Chapter 7

Load the sequencer and start a run

Fill Genexus

™

Primer Pool Tubes (custom assays only)

Genexus

™

Integrated Sequencer User Guide

Содержание Ion Torrent A45727




































































































































































Результаты поиска

Содержание Ion Torrent A45727

Отзывы:

Похожие инструкции для Ion Torrent A45727

Бренды по названию

Популярные бренды

Thermo Scientific Ion Torrent A45727, Руководство пользователя

Результаты поиска

Содержание Ion Torrent A45727

Отзывы:

Похожие инструкции для Ion Torrent A45727

Бренды по названию

Популярные бренды