Thermo Scientific Ion Torrent A45727 Скачать руководство пользователя страница 73

Страница: 73 / 163

To remove any remaining beads

and liquid from the keyholes,

grasp the strip at one end with the

strip seal facing up, then swing

the strip with a rapid, downward

centrifugal arm motion, ending

with a sharp wrist-flick.

Grasp the strip at the other end,

then repeat the centrifugal

motion.

Check tube positions for

significant amounts of beads that

are still trapped in keyholes (see

the following figure), then repeat

the centrifugal motion, if needed.

It is acceptable if a few beads

remain in the keyhole or on the

tube wall, but most should be either in suspension or in a pellet at the

bottom of the tube.

Example Genexus

™

Strip 3

‑

GX5

™

before (upper) and after (lower) inversion. The

carrier has been removed to show tube contents more easily.

Magnetic beads trapped in keyholes

Magnetic beads dislodged from

keyholes

Chapter 7

Load the sequencer and start a run

Before you begin

Genexus

™

Integrated Sequencer User Guide

Содержание Ion Torrent A45727




































































































































































Результаты поиска

Содержание Ion Torrent A45727

Отзывы:

Похожие инструкции для Ion Torrent A45727

Бренды по названию

Популярные бренды

Thermo Scientific Ion Torrent A45727, Руководство пользователя

Результаты поиска

Содержание Ion Torrent A45727

Отзывы:

Похожие инструкции для Ion Torrent A45727

Бренды по названию

Популярные бренды