Thermo Scientific Ion 520 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 78

background image

Guidelines for using Ion Chef

™

consumables and reagents

To ensure the proper function of the Ion Chef

™

System, handle the associated consumables and

reagents according to the following guidelines:

• Store all consumables and cartridges under the recommended conditions and in an upright

position.

• Inspect all consumables and cartridges for damage upon arrival and again before use.
• Hold sequencing chips by gently gripping them by their edges. Do not wear gloves when handling

chips.

• When the instrument is not in use, remove all consumables and reagents from the deck and close

the instrument door.

• Except for the

new

Ion S5

™

ExT Tip Cartridge, do not reuse any of the consumables or reagents.

After each run, transfer the empty Ion S5

™

ExT Tip Cartridge to the waste tip station for use as the

waste container for the next run.

IMPORTANT!

All Ion Chef

™

Instrument components are single-use only.

• Use only Ion Torrent

™

kits and supplies with the Ion Chef

™

Instrument. The use of third-party

reagents and supplies can adversely affect the performance of the Ion Chef

™

Instrument and chips

prepared.

• Remove and sequence chips within 1 hour after the Ion Chef

™

System finishes loading them. If you

cannot sequence a loaded chip immediately, store it within a chip storage container at 4°C until
you are ready to run it (up to 6–8 hours maximum).

IMPORTANT!

If you choose to store a loaded chip, remove the chip from 4°C storage (but keep

it in the chip storage container) at least 20 minutes before running it, allowing the chip to warm to
room temperature.

Prepare the Ion Chef

™

Instrument for use

• Ensure that the Ion Chef

™

Instrument has been cleaned following the previous run. If not, clean the

instrument

before

loading it with consumables.

Note:

For more information on the cleaning procedure, see Chapter 7, “Clean the Ion Chef

• Inspect the empty compartments of the Reagents and Solutions stations for condensation.

Condensate can collect in these compartments, depending on temperature and humidity
conditions. Before loading consumables into the instrument, wipe the compartments dry with a
laboratory wipe or absorbent cloth, if needed.

• Thaw the Ion S5

™

ExT Chef Reagents cartridge at room temperature for 45 minutes before use.

Chapter 2

Before you begin

Guidelines for using Ion Chef

™

consumables and reagents

2

Ion 520

™

& Ion 530

™

ExT Kit − Chef User Guide

15

«
...
13
14
15
16
17
...
»

Содержание Ion 520















































































Отзывы:

Нет отзывов

Похожие инструкции для Ion 520

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

Бренд: XAG Страницы: 24

Бренд: B&G Страницы: 3

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: Gearmore Страницы: 47

Бренд: Xtool Страницы: 51

Бренд: H-TEC Education Страницы: 16

Бренд: H-TEC Education Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды