Thermo Scientific iCAP RQ ICP-MS Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 71

background image

General Pre-Installation Information

Installation

6-4

iCAP RQ Pre-Installation Requirements Guide (P/N BRE0009927, Revision A)

Thermo Scientific

Advanced Training Courses

Thermo Fisher Scientific provides both introductory and advanced
training courses in analytical techniques, together with specialized
operation and maintenance courses for Thermo Scientific products.

Thermo Fisher Scientific recommends that some months after your
instrument has been installed, the key operator receive an advanced
training for the operation and maintenance of the system from Thermo
Fisher Scientific. After this training, the key operator can conduct an
in-house training program on your site for your own people and certify
others to operate the instrument.

For information concerning course schedules and fees, please contact
the following address or your local Thermo Fisher Scientific office:

Thermo Fisher Scientific
Hanna-Kunath-Str. 11
28199 Bremen

Germany

Phone:

+49 (0) 421 - 54 93 0

Fax:

+49 (0) 421 - 54 93 426

E-mail:

[email protected]

Preventive Maintenance

Routine and preventive maintenance of the instrument is in the
responsibility of the operator. Included in this category are the
replacement of worn parts, the exchange of operating resources, and
similar activities.

Regular preventive maintenance is essential, and will increase the life of
the system, result in maximum uptime of the system, and ensure
optimum system performance. Maintenance techniques are covered in
the Operating Manual for your Thermo Scientific instrument. Refer
also to the manufacturers’ manuals shipped with the instrument—
especially for the maintenance of mechanical pumps and
turbomolecular pumps.

«
...
57
58
59
60
61
...
»

Содержание iCAP RQ ICP-MS








































































Отзывы:

Нет отзывов

Похожие инструкции для iCAP RQ ICP-MS

Бренд: Tacx Страницы: 2

Бренд: C.E. Nierhoff & Co Страницы: 7

Бренд: YATEK Страницы: 72

Бренд: Parker Research Corp Страницы: 4

Бренд: Eastwood Страницы: 20

Бренд: Daihan Scientific Страницы: 43

Littmann Classic II Pediatric

Бренд: 3M Страницы: 53

Бренд: Össur Страницы: 16

Exoform Dorsal Night Splint

Бренд: Össur Страницы: 34

Wallach UltraFreeze

Бренд: Cooper Surgical Страницы: 4

Бренд: AGCO Страницы: 44

Aesculap S4 FW103R

Бренд: Braun Страницы: 39

Бренд: Heitronic Страницы: 8

Life/form LF03608

Бренд: Nasco Healthcare Страницы: 6

Бренд: Beta Страницы: 8

Бренд: Harken Industrial Страницы: 2

Бренд: Basko Healthcare Страницы: 2

KEW FORK 2300 R

Бренд: KYORITSU Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды