Thermo Scientific GENESYS 10S Vis Скачать руководство пользователя страница 94

Страница: 94 / 134

Concentration Measurements—Standard Curve Application

Measuring Samples

GENESYS 10S Vis User Guide

Thermo Scientific

If a 6-Position Cell Holder is installed, press the cell position buttons to reposition the cell
holder and measure the rest of the standards manually.

When all of the standards have been measured, the Standards screen (see

“Using the

Standards Screen”

page 86

) shows the absorbance of each standard, along with the

slope, intercept and correlation coefficient of the standard curve.

Using the Standards Screen

Here is an example of the Standards screen showing measurement results:

You can use this screen for:

• Displaying a graph of the standard curve data (press

View Graph

)

•

Saving a Test

(press

Save Test

)

•

Editing a Standard Curve

(press

Edit Standards

)

•

Measuring Samples

(press

Run Test

)

Measuring Samples

To measure samples automatically using the calibration curve (using Auto 6 or Auto
3)

1. Press

Run Test

2. Install the blank and samples.

3. Press

Enter

The Standard Curve screen shows the absorbance and concentration of each sample.

To switch between tabular and graphical displays, press

View Graph/Tabular

Содержание GENESYS 10S Vis







































































































































Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды

Thermo Scientific GENESYS 10S Vis, Руководство пользователя

Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды