Thermo Scientific DensityPRO+ Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 107

background image

Wiring

Serial Communications

Optional RS485

Wiring

Connecting a PC serial port (COM) to the optional RS485 port on the
gauge requires an RS485/RS232 converter (p/n 670045). The J6 connector
on the transmitter CPU is for the RS485 connections. Refer to installation
wiring drawing

and make the RS485 connections as follows.

1.

CDATA and –DATA on the RS485 connector (J6) to the
corresponding connections on the RS485/RS232 converter.

2.

Connect the RS485/RS232 converter to the PC using a standard DB9
serial cable.

RS485 Termination

If you are having trouble using another device on the RS485 chain, verify
that it is properly terminated for its position on the chain. To terminate a
device, connect a 120



resistor between its RS485 +/– data terminals.

Never terminate more than the first and last device in the chain.

The transmitter includes a three-pin header (W4), located near the bottom-
front edge of the CPU board next to the RS485 connector (J6), to
terminate the RS485 connection.

For a single unit installation or for a multiple unit installation where the
transmitter is the last unit in line, the W4 jumper should be placed on pins
1 and 2 to terminate the RS485 line.

For a multiple unit installation where the transmitter is the not last unit in
line, the W4 jumper should be placed on pins 2 and 3 so that the RS485
line is not terminated at the transmitter.

RS232 Wiring

COM1 or COM2 on a PC can be connected directly to the transmitter
RS232 port. This connection requires five wires: ground, TX, RX, RTS,
and CTS. The RS232 port connector (J8) is located on the transmitter
CPU board. Connections for standard DB9 and DB25 PC serial port
connectors are listed in the table below.

Table

4–8.

RS232 connections

RS232 Connector (J8) on
Transmitter CPU

PC Serial Port DB9
Connector

PC Serial Port DB25
Connector

J8-1 (RTS)

Pin 8

Pin 5

J8-2 (TX)

Pin 2

Pin 3

J8-3 (CTS)

Pin 7

Pin 4

J8-4 (RX)

Pin 3

Pin 2

J8-5 (GND)

Pin 5

Pin 7

4-14

Den Installation Guide

Thermo Fisher Scientific

«
...
42
43
44
45
46
...
»

Содержание DensityPRO+












































































































Отзывы:

Нет отзывов

Похожие инструкции для DensityPRO+

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

SimMan 3G Trauma

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 60

Бренд: laerdal Страницы: 4

Resusci Anne Simulator

Бренд: laerdal Страницы: 8

Nursing Baby VitalSim

Бренд: laerdal Страницы: 15

Бренд: Mackie Страницы: 34

Бренд: Mackworth Страницы: 38

Бренд: P&P Страницы: 6

Бренд: Maico Страницы: 55

Бренд: Maico Страницы: 38

Бренд: Maico Страницы: 2

Бренд: MAHA Maschinenbau Haldenwang Страницы: 13

Бренд: QRS Страницы: 16

Бренд: QMAXZ Lighting Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды