Thermo Scientific AI 3000 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 108

background image

Declaration

Manufacturer:

Thermo Fisher Scientific

Thermo Fisher Scientific is the manufacturer of the instrument described in this manual and, as such, is responsible
for the instrument safety, reliability and performance only if:
•

installation

•

re-calibration

•

changes and repairs

have been carried out by authorized personnel and if:
•

the local installation complies with local law regulations

•

the instrument is used according to the instructions provided and if its operation is only entrusted to qualified
trained personnel

Thermo Fisher Scientific is not liable for any damages derived from the non-compliance with the aforementioned
recommendations.

Regulatory Compliance

Thermo Fisher Scientific performs complete testing and evaluation of its products to ensure full compliance with
applicable domestic and international regulations.

When the system is delivered to you, it meets all pertinent electromagnetic compatibility (EMC) and safety
standards.

Safety

This device complies with EN 61010-1:2001, EN 61010-2:2002 according to Low Voltage Directive 2006/95/EC.

Electromagnetic Compatibility

This device complies with EN 61326-1:2006 according to directive 2004/108/EC.

FCC Compliance Statement

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

CAUTION

Read and understand the various precautionary notes, signs, and symbols contained

inside this manual pertaining to the safe use and operation of this product before using the device.

«
...
3
4
5
6
7
...
»

Содержание AI 3000













































































































Отзывы:

Нет отзывов

Похожие инструкции для AI 3000

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: GE Страницы: 802

Бренд: iET Страницы: 17

Бренд: Parr Instrument Страницы: 24

Бренд: JBL Страницы: 15

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренд: Cabletron Systems Страницы: 33

Бренд: i-CAT Страницы: 32

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: U-Line Страницы: 3

Бренд: U-Line Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды