Thermo Scientific Agilent 1200 Series Скачать руководство пользователя страница 46

Страница: 46 / 58

Connecting the Communication Cables

Connecting the Ethernet Cables

Agilent 1200 Series Getting Connected Guide for LC Devices

Thermo Scientific

Connecting the Ethernet Cables



To connect the Ethernet communication cable to an Agilent LC stack

1. Connect one Ethernet cable from the LAN interface port (

Figure 24

) to the Ethernet

switch.

Figure 24.

Ethernet connection to the two types of LAN interfaces

2. Connect the second Ethernet cable from the Ethernet switch to the Ethernet network

card in the data system computer that is dedicated to the LC/MS system (typically
network interface card number 3).

CAUTION

Safety and EMC regulations require the use of Category 5 shielded Ethernet

communication cables, maximum 3 m (10 ft) long.

REMOTE

RS-232

CONFIG

ANALOG

CAN

Agilent Technologies

Activity

Speed

G1369 LAN Interface

LAN

USB

REMOTE

RS-232

CAN

CONFIG

REMOTE FLASH

PCMCIA

ANALOG

CONFIG

Agilent LAN interface card
(Model G1369)

On-board LAN interface
port on the detector

Connects to the
Ethernet switch.

Initialization switches

Connects to the
Ethernet switch.

Содержание Agilent 1200 Series



























































Результаты поиска

Содержание Agilent 1200 Series

Отзывы:

Похожие инструкции для Agilent 1200 Series

Бренды по названию

Популярные бренды

Thermo Scientific Agilent 1200 Series, Руководство по подключению

Результаты поиска

Содержание Agilent 1200 Series

Отзывы:

Похожие инструкции для Agilent 1200 Series

Бренды по названию

Популярные бренды