manualshive.com logo in svg

Thermo Scientific A55867, Руководство пользователя

Поделиться
Скачать
Thermo Scientific A55867 Скачать руководство пользователя страница 54

Create protocol steps

This is the Create step view, which is where the actual protocol is programmed in a stepwise manner.
More details about the different functionalities are shown, see Table 2.

Note: 

At a high-level, there are three parameters that can be set in a step, which are: magnet, rocker,

and pump. The setting of these should be considered for each step.

1

4

7

5

6

8

9

10

11

12

3

2

1

Start/end point of fluid lines

2

Engage/disengage magnet

3

Engage/disengage continous rocking

4

Start point of air

5

Add prompts

6

Rocker settings

7

Bubble sensor settings

8

Pump settings

9

Create next step by duplicating current

10

Navigate steps

11

Cancel protocol writing

12

Review all steps

Table 2   Features of the Create step view

Feature

Details

Magnet

Can be on or off.

When a duration is set for the magnet, it determines how long the rocker will be in the
specified position before moving to the next step.

Rocker

When off, a static angle can be set, when on, continuous rocking is specified.

Angle range: -30° to +30°

Speed range (cycles per minute): 1–30 CPM

The rocking can be symmetric (e.g. -10° to 10°) or “asymmetric” (e.g. -5° to 30°).

Chapter 3 

Embedded graphical user interface (eGUI) user instructions

Manage protocols

3

54

CTS

™

 DynaCellect

™

 Magnetic Separation System User Guide

Содержание A55867







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды