Thermo Scientific 75004559 Скачать руководство пользователя страница 46

Страница: 46 / 58

Trouble Shooting

Troubleshooting by User

Thermo Scientific

Heraeus Multifuge X3F / X3FR

7-3

5. Reconnect the centrifuge once the power has been restored. Switch on the centrifuge. Press the

OPEN key

to have the door locks operative again.

Troubleshooting by User

WARNING

If you pull only one lever or you do not pressed the OPEN key

to have

the door locks operative again, the door might open while the rotor os still spinning.

If problems occur other than those listed in this table, the authorized customer service

representative must be contacted.

Failure message

Problem with centrifuge

Possible causes and cures

The centrifuge cannot be operated.

Overtemperature

The run does not start or the centrifuge runs
down without being braked.

Overheating in chamber.

Check the function of the refrigeration unit.

Clean the air inlet for the condenser.

Restart the centrifuge.

If an error message appears again, inform Customer Service.

The centrifuge cannot be operated.

Incorrect bucket ID

The run does not start or the centrifuge runs
down without being braked.

Bucket code is undefined for the rotor detected, check the set

points for the given bucket code.

Is it permitted to use the current bucket in the rotor currently

mounted?

Restart the centrifuge.

If an error message appears again, inform Customer Service.

The centrifuge cannot be operated.

Unapproved rotor

The run does not start or the centrifuge runs
down without being braked.

Rotor code is not in the rotor table.

Is it permitted to use the rotor currently mounted in this device?

Restart the centrifuge.

If an error message appears again, inform Customer Service.

The centrifuge cannot be operated.

Rotor ID failure

The run does not start or the centrifuge runs
down without being braked.

The rotor could not be identified.

Check to see if the rotor is properly installed.

Restart the centrifuge.

If an error message appears again, inform Customer Service.

Restart the centrifuge.

Centrifuge does not open

Lid blocked

The emergency lid release enables you to retrieve your samples.

If an error message appears again, inform Customer Service.

The centrifuge cannot be operated.

Motor overtemp.

The run does not start or the centrifuge runs
down without being braked.

Restart the centrifuge.

If an error message appears again, inform Customer Service.

Содержание 75004559



























































Результаты поиска

Содержание 75004559

Отзывы:

Похожие инструкции для 75004559

Бренды по названию

Популярные бренды

Thermo Scientific 75004559, Инструкция по эксплуатации

Результаты поиска

Содержание 75004559

Отзывы:

Похожие инструкции для 75004559

Бренды по названию

Популярные бренды