Thermo Scientific 074114 страница 68 Скачать руководство пользователя | Manualshive

Страница: 68 / 148

background image

Dionex PDA Operator’s Manual

60

Doc. 065378-01 1/12

The table below lists the Dionex PDA-related error messages and their default
severity levels. For troubleshooting assistance, refer to the page indicated in the
table.

Dionex PDA-Related Alarms and Error Conditions

Default Severity
Level

See

3DFIELD RefWavelength and/or RefBandwidth is out of
range.

Error

Acquisition On for 3DFIELD rejected—no 3D Data
Acquisition license found.

Abort

Autozero is already in progress.

Error

Calibration is running.

Abort

Cannot change 3DFIELD parameters while data
acquisition is running.

Warning

Cannot set manual parameters for the required operation
because the DSP is not ready.

Abort

Can’t execute calibration command during data
acquisition.

Error

Can’t execute diagnostic command during data
acquisition.

Error

Can’t execute x command during data acquisition.

Error

Command not executed because an Autozero command
is already running.

Warning

Data is unavailable.

Abort

Diagnostic is running.

Abort

DSP communication failure.

Abort

Filter wheel sensor could not detect blocked position.

Warning

Filter wheel sensor could not detect open position.

Warning

Invalid rise time. Valid rise times at 20 Hz: 0.05, 0.1, 0.2,
0.5, 1.0, and 2.0.

Abort

Invalid step for the 3DFIELD. Valid steps are 0.05, 0.1, 0.2,
0.4, 0.5, 1, 2, and 4.

Error

Leak sensor error.

Warning

Not enough light to perform operation.

Warning

Over temperature error.

Abort

PDA is running a calibration or diagnostic function. Not
ready to accept this command.

Error

«
...
66
67
68
69
70
...
»

Содержание 074114





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 074114

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 4

BB-HCE481A - Network Camera

Бренд: Panasonic Страницы: 2

BL-C30A - Wireless 802.11 b/g Network Camera

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 2

AWE300 - COLOR CAMERA

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 4

AKHC910 - 1080I CAMERA

Бренд: Panasonic Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды