background image

All installations and services must be performed by qualified service personnel. 

IF SYSTEM IS IN LOCKOUT, 

THE MODULE WILL RESET 

ITSELF AFTER 60 MINUTES 

OR MAY BE MANUALLY 

RESET BY INTERRUPTING 

THE POWER TO THE FURNACE 

AT THE DISCONNECT OR 

INTERRUPTING THE CALL FOR 

HEAT AT THE THERMOSTAT.  

IF THIS DOES NOT RESTART 

THE SYSTEM, REFER TO THE

TROUBLESHOOTING SECTION 

OF THIS MANUAL.

AFTER THE DELAY-TO-FAN-OFF

PERIOD ENDS, THE CIRCULATING

AIR FAN AND (OPTIONAL) ELECTRONIC

AIR CLEANER ARE DE-ENERGIZED.

AFTER DELAY-TO-FAN-ON PERIOD 

ENDS (45 SECONDS), CIRCULATING 

AIR FAN IS ENERGIZED AT LOW 

FIRE HEATING SPEED OR HIGH 

FIRE IF W2 IS ENERGIZED.  THE 

(OPTIONAL) ELECTRONIC AIR

CLEANER AND HUMIDIFIER 

ARE ENERGIZED.

IF THERMOSTAT

W2 CONTACTS 

ARE CLOSED

OTHERWISE

CALL

FOR

HIGH

FIRE

NO CALL

FOR 

HIGH FIRE

THERMOSTAT CLOSES W2 

CALLING FOR HIGH FIRE 

HEATING.  

GAS VALVE, INDUCER AND 

AIR FAN ARE ENERGIZED 

TO HIGH FIRE SETTINGS

WHEN THERMOSTAT W1 IS SATISFIED,

CONTACTS OPEN AND THE GAS 

VALVE IS DE-ENERGIZED. AFTER 

PROOF OF FLAME LOSS, INDUCER 

STARTS 5 SECOND POST PURGE 

AND (OPTIONAL) HUMIDIFIER IS 

DE-ENERGIZED.  THE DELAY-TO-

FAN-OFF PERIOD BEGINS (120 SECONDS)

WHEN THERMOSTAT HAS 

SATISFIED W2, CONTACTS 

OPEN AND THE GAS VALVE 

AND AIR FAN HIGH FIRE 

SETTINGS ARE DE-ENERGIZED

AFTER 30 SECOND DELAY.

 

38 

Содержание CDX3-100N




































































Отзывы: