Thermo King SR-2 SmartReefer2 Скачать руководство пользователя

Страница: 369 / 431

Section 6 – SR-2 Service Procedure A49A

CargoWatch Time and Date

The time and date used by the CargoWatch data logger is held in the HMI Control Panel. To set or change the

date and time use the Set Time and Date feature at the end of the Maintenance Menu. The time and date can

also be set or changed by using Wintrac 4.4.

The HMI Control Panel will update the SR-2 Controller and the ServiceWatch data logger with the correct time

and date each time the unit is turned on.

Downloads

To download the datalogger connect the download cable to the CargoWatch port on the unit. Downloads are

obtained using Wintrac 4.4.

Printing Reports

Trip Reports and Delivery Reports can be directly printed. The printer must be connected to the printer port

connector located inside the unit control box. This port may be routed to the outside of the unit as required by the

individual user.

Programmable Features

The CargoWatch data logger programmable features are set from the Sensor Configuration Sub-menu in the

Guarded Access menu. The sensor features allow the logging interval to be set and the sensors and digital

inputs to be enabled, named, and tailored to customer requirements. The flowchart on the next page illustrates

the features and menu flow. See Section 3 of this manual for complete information on CargoWatch

programmable features.

Programmable features may also be set up using Wintrac 4.4.

Factory defaults have the Setpoint and CargoWatch Sensors 1 and 2 turned On. CargoWatch Sensors 3 through

6 and Digital Inputs 1 through 4 are turned Off.

Page 3

P41RA49A 31 January 2005

Содержание SR-2 SmartReefer2
















































































































































































































































































































































































































































Результаты поиска

Содержание SR-2 SmartReefer2

Отзывы:

Похожие инструкции для SR-2 SmartReefer2

Бренды по названию

Популярные бренды

Thermo King SR-2 SmartReefer2, Руководство по диагностике

Результаты поиска

Содержание SR-2 SmartReefer2

Отзывы:

Похожие инструкции для SR-2 SmartReefer2

Бренды по названию

Популярные бренды