background image

 

 

Electric boilers MINI BTH 

Installation & Operating Manual (Revision: May 2015),                                                               

5

 

Section 3 : INSTALLATION 

 

 
The  manufacturer’s  warranty  does  not  cover  any  damage  or  defect  caused  by  installation,  or 
attachment,  or  use  of  any  special  attachment  other  than  those  authorized  by  the  manufacturer 
into,  onto,  or  in  conjunction  with  the  boiler.  The  use  of  such  unauthorized  devices  may  shorten 
the  life  of  the  boiler  and  be  dangerous.  The  manufacturer  disclaims  any  responsibility  for  such 
loss or injury resulting from the use of such unauthorized devices. 

 

3.1 SAFETY MEASURES 

All  installation  will  include  the  supplied  pressure 
relief  valve  which  limits  the  maximum  operating 
pressure to 30 psi (207 kPa). 
 
This electric boiler is designed to be installed on 
a circuit operated between 50°F to 190F (10C to 
90C)  and  at  a  maximum  operating  pressure  of 
30psi  (207kPa).  The  unit  in  designed  solely  to 
be  used  on  a  close  loop  hydronic  heating 
system.  The  heat  transfer  solution  must  be  a 
solution  of  water  or  a  mix  solution  Water/Glycol 
having a maximum glycol concentration of 50%. 
The boiler high limit temperature control is set at 
a fixed temperature of 210F 99C). If the heating 
distribution  system  on  which  the  boiler  is 
installed requires a high limit controller having a 
lower setting, this controller will be added to the 
system and connected  in series  with the factory 
installed limit control. 

 
3.2

 

LOCATION 

The electric boiler should be installed in a clean, 
dry  location.    Long  hot  water  lines  should  be 
insulated  to  conserve  water  and  energy.    The 
electric  boiler  and  water  lines  should  be 
protected 

from 

exposure 

to 

freezing 

temperature. 
The  boiler  can  be  mounted  vertically  or 
horizontally  directly  on  a  solid  surface  with  4 
adequate  screws  inserted  in  the  provided  boiler 
openings. Make sure it is properly leveled. 
The  electric  boiler  must  be  located  or  protected 
so  as  not  to  be  subject  to  physical  damage,  for 
example, by moving vehicles, area flooding, etc. 
All  models  can  be  installed  directly  on  a 
combustible  wall  and  into  an  alcove.  The 
location  must  have  sufficient  ventilation  to 
maintain  an ambient temperature  not  exceeding 
90F (32C). 

 

 
The  electric  boiler  should  not  be  located  in 
an  area  where  leakage  of  its  tank  or  water 
connections  will  result  in  damage  to  the 
adjacent  area  or  to  lower  floors  of  the 
structure.    When  such  areas  cannot  be 
avoided,  install  a  suitable  drain  pan  or  non-
flammable catch pan under the unit to collect 
the  water.  The  pan  must  be  connected  to  a 
drain. 
NOTE: Auxiliary catch pan MUST conform to 
local codes. 

 
3.3 CLEARANCE   

For adequate inspection and servicing the 
following minimum clearance is necessary: 
 

Table 3: boiler clearances 

Sides 

3 inches 

 Electric elements side  

14 inches 

Front side of the boiler 

3 inches* 

Back  

0 inch 

 
*If  the  boiler  is  installed  in  a  closed 
compartment,  allow  an  access  service  opening 
and adequate ventilation to maintain an ambient 
temperature lower than 90F/32C. 

 

WARNING 

   ! 

 

CAUTION 

  ! 

Содержание MINI BTH
















Отзывы: