manualshive.com logo in svg

Thermal Dynamics SL100 HAND TORCH, Инструкция по эксплуатации

Поделиться
Скачать
Thermal Dynamics SL100 HAND TORCH Скачать руководство пользователя страница 23

Manual 0-2962

3-3

INSTALLATION

3. Secure the Through - Hole protector with the re-

taining nut removed earlier.

4. Connect the torch leads or ATC Adapter Negative

/ Plasma Lead to the bulkhead connection inside
the Power Supply as shown.

Adapter

Plug

Pilot Lead

Torch Leads
Assembly or

ATC Adapter

Negative/Plasma

Lead

Adapter

Connector

Pilot Lead Stud

Negative/Plasma Lead

Connection

A-03527

Control Circuit

Connectors

Note: Actual Bulkhead 
configuration may
differ from that shown.

Bulkhead Connections - ATC Adapter or Hand

Torch Leads with O2B Fittings

5. The Leads or ATC Adapter Assembly includes two

wires joined with mating connectors and covered
with an insulating sleeve.  These wires must re-
main joined and insulated.  Connect the remain-
ing torch leads  connectors to the mating connec-
tors on the Power Supply Adapter.

6. Remove the top nut and washer from the Pilot

Stud.

7. Connect the pilot lead terminal to the stud and

secure with the nut and washer removed in the
above Step.

8. Tighten the Through - Hole protector onto the

Torch Leads or ATC Adapter Leads Assembly.

9.

For torches with the ATC Connector

, align the

torch leads male connector with the ATC female
receptacle.  Push the male connector into the fe-
male receptacle.  The connectors should push to-
gether with a very small amount of pressure.  Se-
cure the connection by turning the locking nut
clockwise until it stops.  DO NOT use the locking
nut to pull the connection together.  Do not use
tools to secure the connection.

A-03627

1

2

ATC Male 
Connector

ATC Adapter 
Female Receptacle 

Torch Leads

To 

Power Supply

Torch Connection - Torch Leads with ATC Male

Connector, Power Supply with ATC Adapter

1

2

Control Cable
Connector (Machine 
Torches Only)

ATC Male 
Connector

ATC Female Receptacle 
(Panel Mounted)

A-03602

Torch Connection - Torch Leads with ATC Male

Connector, Power Supply with Panel-Mounted ATC

Receptacle

10. Check the torch for proper consumable parts.

CAUTION

The torch parts must correspond with the type of
operation.  Refer to Section 4.04, Torch Parts Se-
lection.

Содержание SL100 HAND TORCH





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды