manualshive.com logo in svg

Thermal Dynamics 38 Cutmaster, Руководство по эксплуатации, Страница: 19 / 51

Поделиться
Скачать
Thermal Dynamics 38 Cutmaster Скачать руководство пользователя страница 19

Manual 0-2888

3-5

INSTALLATION

D. Using High Pressure Gas Cylinders

When using high pressure gas cylinders as the gas supply:

1. Refer to the manufacturer’s specifications for installation and maintenance procedures for high pressure gas

regulators.

2. Examine the cylinder valves to be sure they are clean and free of oil, grease or any foreign material.  Briefly open each

cylinder valve to blow out any dust which may be present.

3. The cylinder must be equipped with an adjustable high - pressure regulator capable of outlet pressures up to 100 psi

(6.9 bar) maximum and flows of at least 300 scfh (141.5 lpm).

4. Connect  gas supply hose to the cylinder.

NOTE

Pressure should be set at 100 psi (6.9 bar) at the high pressure gas cylinder regulator.

Supply hose must be at least 1/4 inch (6 mm) I.D.

For a secure seal, apply thread sealant to the fitting threads, according to manufacturer's instructions.  Do Not use
Teflon tape as a thread sealer, as small particles of the tape may break off and block the small gas passages in the torch.

Содержание 38 Cutmaster




















































Отзывы:

Нет отзывов