Thermador PRG486JDG/01 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 91

Thermador PRG486JDG/01 Скачать руководство пользователя страница 11

Service Manual for the Thermador Pro Grand Next Generation 48-Inch Natural Gas and LP Gas Ranges, Models:

PRG486JDG/01, PRL486JDG/01

58300000159722_ARA_EN_D

Page 12 of 92

3 TESTING, ADJUSTING, AND TROUBLESHOOTING

RANGETOP BURNERS AND IGNITION

Servicing Burners and Ignition

Burner and ignition servicing must be performed by a qualified
technician. Improper adjustments may be dangerous, cause damage
or harmful by-products, and may void the appliance warranty.

Ignition Hazard

Do not touch burners when the igniters are active (sparking).

3.1 Before Testing

Before testing rangetop burners and ignition, do the following:

1. Reinstall any loose components that may have been removed

earlier, such as burner caps, griddle/grill, and grates. Be
certain that burner caps seat properly into the burner bases,
burner bases and Venturi tubes are aligned correctly, and that
the ignition wires are properly positioned.

2. To test for gas leaks, make sure the electrical power is

removed and the manual gas shut-off valve is open, and then
carefully check range components and gas supply for leaks
using a gas leak detector or bubble test.

3. After gas checks are complete and before testing, connect the

range to the electrical power supply.

3.2 Rangetop Burner Characteristics

If one or more rangetop burner blows out, the respective igniter
electrode automatically re-ignites the flame.

The flame should burn through each burner port, completely around
the burner cap (see Figure 4).

Figure 4: Burner Ports

1

Burner ports

It is normal to hear the following during burner operation:

•

A slight sound that is associated with gas combustion and ignition.

There should not be a loud noise.

•

A clicking noise every time the gas cycles, coming from the

solenoid valves of the two left burners

•

If using LP gas, a slight “pop” sound may be heard at the burner

ports a few seconds after the burner has been turned off.

«
...
9
10
11
12
13
...
»

Содержание PRG486JDG/01




























































































Отзывы:

Нет отзывов