manualshive.com logo in svg

THERMACUT EX-TRAFIRE 45HD, Руководство оператора

Поделиться
Скачать
THERMACUT EX-TRAFIRE 45HD Скачать руководство пользователя страница 51

EX-TRAFIRE

®

45SD

Operator Manual, Revision T-5

4-51

Mechanized Cutting Charts 

45 A Cutting, Shielded Configuration

EX-2-401-201

EX-2-404-201

EX-2-409-201

EX-2-415-201

EX-2-421-201

***

EX-2-415-202

EX-2-421-201

EX-2-423-211

EX-2-428-011

Notes:

* Cut capacity speeds are not necessarily maximum speeds� 

They are the speeds that must be achieved to be rated at that 

thickness�

** Maximum cut speeds are the results of intensive laboratory 

testing�  

Actual cutting speeds may vary based on different cutting 

applications� 

Cut charts are a guide for mechanized cutting, individual 

systems can be “fine tuned” to achieve optimum cut quality�

*** Unshielded configuration 

When using unshielded consumables, adjust the torch to 

work height manually or adjust the Arc Voltage Control (AVC) 

settings to produce the desired cut quality�

Содержание EX-TRAFIRE 45HD

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды