THERMACUT EX-TRAFIRE 40SD Скачать руководство пользователя

Страница: 8 / 72

EX-TRAFIRE

40SD

Operator Manual, Revision T-15

Gas cylinders which contain gas under high pressure can
rupture and explode if damaged�

•

Handle and use compressed gas cylinders in accordance
with local or national codes�

•

Never allow electrical contact between the plasma arc
and a cylinder�

•

Never expose cylinders to excessive heat, sparks, slag or
flames�

CAUTION WHEN CUTTING

AROUND GAS CYLINDERS

Plasma Arc Cutting

Current

Protection glass

shade number*

Up to 150A

ISO (DIN) 11

150A to 250A

ISO (DIN) 12

250A to 400A

ISO (DIN) 13

OVER 400A

ISO (DIN) 14

* According to ISO 4850:1979

Induction heating of certain materials, adhesives, and fluxes
may cause fumes or smoke�

Breathing the fumes and smoke can be hazardous to your
health

•

Keep your face out of the smoke, do not breathe the
fumes�

•

Use local exhaust ventilation for fume removal�

•

If ventilation is poor, wear an approved air-supplied
respirator�

SMOKE AND GASES CAN

BE HAZARDOUS

•

Work in a confined space only if it is well ventilated,
or while wearing an air-supplied respirator� The
smoke and gases from the cutting/gouging process
can displace air and lower the oxygen level causing
injury or death�

•

Monitor the breathable air quality as required�

MAGNETIC FIELD CAN

AFFECT PACEMAKERS

•

People with pacemakers/hearing aids should avoid
close contact with plasma arc power supply�

•

People with pacemakers/hearing aids should consult
their doctor before operating plasma arc power
supply�

Do not exceed the recommended duty

cycle, this can lead to overheating

and cause damage to the system�

•

Allow a suitable cooling off period with high demand
usage�

•

Observe the duty cycle rating shown on the label
attached to the system�

PLASMA CUTTING CAN

CAUSE INTERFERENCE

•

Electromagnetic energy can interfere with sensitive
electronic equipment such as computers, or
computer-driven equipment�

•

Ensure that all equipment in the cutting area is
electromagnetically compatible�

•

Ensure that the plasma arc cutting system is installed
and positioned in accordance with this manual�

Содержание EX-TRAFIRE 40SD









































































Результаты поиска

Содержание EX-TRAFIRE 40SD

Отзывы:

Похожие инструкции для EX-TRAFIRE 40SD

Бренды по названию

Популярные бренды

THERMACUT EX-TRAFIRE 40SD, Руководство оператора

Результаты поиска

Содержание EX-TRAFIRE 40SD

Отзывы:

Похожие инструкции для EX-TRAFIRE 40SD

Бренды по названию

Популярные бренды