THERMACUT EX-TRAFIRE 40SD Скачать руководство пользователя

Страница: 60 / 72

EX-TRAFIRE

40SD

Operator Manual, Revision T-15

9-60

Filter-EX Compressed Air Filter with replacement filter cartridge

EX-0-804-001

Filter-EX Compressed Air Filter

(Standard package 1 piece)

EX-0-804-002

Filter-EX Air Filter Cartridge

(Standard package 8 pieces)

Technical specification

Filtering Degree:

0�01 μinch – 0�25 μm

Maximum Pressure:

125 PSI – 8�5 bar

Maximum Flow @ 80%:

2700 SCFH – 1250 l/min�

Temperature Range:

15 – 140F / −10 +60 °C

Size Pipe:

¼ NPT

Dimension:

Ø 5�2“ × 7�9“ – Ø 132 × 200 mm

This filter does not fall under the specification of pressure equipment and requires no revision�

Advantages of using the Filter-EX Compressed Air Filter:

•

Removes solid particles, aerosols, and moisture from the compressed air�

•

Elimination of the negative effects caused by humidity during cutting�

•

Extends the service life time of the torch, leads and consumables�

•

Reduces the risk of torch and power supply damage�

•

Positive effect on the quality of the cut�

Filter-EX Quick Connect Couplings

EX-0-802-000

DN 7�2 ES Quick Connect Plug

with female thread G 1/4“

EX-0-802-001

DN 7�2 ES Quick Connect Plug

with male thread G 1/4“

EX-0-802-002

DN 7�2 ES Quick Connect Coupling

with male thread G 1/4“

SECTION 9: ACCESSORIES

SECTION 9�

ACCESSORIES:

Содержание EX-TRAFIRE 40SD









































































Результаты поиска

Содержание EX-TRAFIRE 40SD

Отзывы:

Похожие инструкции для EX-TRAFIRE 40SD

Бренды по названию

Популярные бренды

THERMACUT EX-TRAFIRE 40SD, Руководство оператора

Результаты поиска

Содержание EX-TRAFIRE 40SD

Отзывы:

Похожие инструкции для EX-TRAFIRE 40SD

Бренды по названию

Популярные бренды