THERMACUT EX-TRAFIRE 40SD Скачать руководство пользователя

Страница: 34 / 72

EX-TRAFIRE

40SD

Operator Manual, Revision T-15

4-34

Torch consumables installation

WARNING

Plasma arc is generated immediately

when the torch trigger is depressed

Plasma arc is generated immediately when the torch trigger is depressed�
The plasma arc will cut quickly through gloves and skin� Make sure the power is switched off before
changing consumables�

1� Screw the electrode� Use the electrode wrench

(EX-2-427-010)� Do NOT overtighten electrode�

4� Fit the nozzle on to

the swirl ring�

5� Screw on the nozzle

retaining cap and tighten by

hand� Do NOT overtighten�

2� Insert the swirl ring with beveled edge in the

torch body� Must seated properly�

3� Perform free movement test of the electrode inside

the swirl ring (by pushing the electrode)�

6� Screw on the hand (contact) shield (tighten by hand)� Do NOT overtighten�

Machine Shield

Deflector

Hand Shield

Содержание EX-TRAFIRE 40SD









































































Результаты поиска

Содержание EX-TRAFIRE 40SD

Отзывы:

Похожие инструкции для EX-TRAFIRE 40SD

Бренды по названию

Популярные бренды

THERMACUT EX-TRAFIRE 40SD, Руководство оператора

Результаты поиска

Содержание EX-TRAFIRE 40SD

Отзывы:

Похожие инструкции для EX-TRAFIRE 40SD

Бренды по названию

Популярные бренды