#ONTROL 0ANEL
Master Power Switch:
The Master Power Switch located on
the left side of the control panel can be used to turn the
UNIT /. /&& OR SET THE UNIT TO BE CONTROLLED BY AN EXTERNAL
thermostat.
7HEN SET TO /. THE &URY WILL ENERGIZE THE BLOWER AND
CLOSE THE HEATER CONTACTORS CONTINUOUSLY $EPENDING ON
the connected power sources, the corresponding heater
ELEMENTS WILL BE ENERGIZED )N THIS MODE THE &URY IS
LIMITED TO & INCOMING AIR TEMPERATURE BY AN INTERNAL
thermostat.
7HEN SET TO 4(%2-/34!4 THE BLOWER WILL RUN CONTINUOUSLY
but the heating contactors will only energize when the
thermostat terminals (located under the lid) are connected
by a switch, remote thermostat, timer, etc.
Heat ON/OFF Switches:
These switches individually
CONTROL THE 6!#7 HEATING ELEMENTS %ACH
switch connects and disconnects the power from the
receptacle below it. These switches are lighted to indicate
when power is connected and the corresponding heating
element is on.
(OUR -ETER
The digital hour meter measures the cumulative time that
THE UNIT IS TURNED ON TO TENTHS OF AN HOUR )T STORES AND
DISPLAYS THE TOTAL WHEN THE UNIT IS UNPLUGGED )T RESETS TO
zero after 99,999.9 hours of operation.
2EMOTE 4HERMOSTAT #ONNECTION
To connect the included remote thermostat, first locate
the thermostat terminals under the lid of the FireBird Fury.
There are 2 spring loaded terminals for connecting the
THERMOSTAT WIRING #ONNECT ONE WIRE TO EACH TERMINAL )F
the FireBird Fury is placed inside the space to be heated,
place the thermostat on top of the unit. For applications
where the FireBird Fury is placed outside the space to be
heated (e.g. ducting heat into a chamber), the 25’ cord
allows you to place the thermostat inside the heated
space.
)N ADDITION TO THE INCLUDED THERMOSTAT ANY DRYCONTACT
switch or other type of control that connects the terminals
together will cause the heating elements to run. The
4
WWW5SE0HOENIXCOM s SALES 5SE0HOENIXCOM
4OLL&REE
THERMOSTAT CIRCUIT IS LOW VOLTAGE 6!# $/ ./4
#/..%#4 0/7%2 4/ 4(% 4(%2-/34!4 4%2-).!,3
Always press terminal levers to release spring pressure
before disconnecting thermostat wiring. Failure to do so
WILL LEAD TO EXCESSIVE WEAR ON SPRING LOADED TERMINAL
connector.
-AINTENANCE
!IR &ILTER
4HE 0HOENIX &IRE"IRD &URY IS EQUIPPED WITH A PLEATED FABRIC
AIR lLTER THAT MUST BE CHECKED REGULARLY 4HE STANDARD
lLTER IS A -%26 HIGH EFlCIENCY lLTER /PERATING THE
FireBird Fury with a dirty or obstructed filter will reduce
AIRmOW EVENTUALLY CAUSING THE HEATING ELEMENT TO SHUT
OFF )NSTALLING A CLEAN lLTER OR REMOVING THE OBSTRUCTION TO
RESTORE AIRmOW WILL ALLOW THE HEATING ELEMENT TO OPERATE
again.
The filter can generally be vacuumed clean several times
before needing replacement. Replacement filters can be
ordered from the factory or purchased locally if available.
WARNING: DO NOT operate the unit without the filter or
with a less effective filter as the heating coils inside the
unit could become clogged and require disassembly to
clean.
3ERVICE
WARNING: Servicing the Phoenix FireBird Fury with its
high voltage circuitry presents a health hazard which
could result in death, serious bodily injury, and/or property
damage. Only qualified service people should service this
unit.
Do not operate the unit without the front panel in place.
High voltage is present, heater burnout may result.
4ECHNICAL $ESCRIPTION
4HE 0HOENIX &IRE"IRD &URY USES A WOUND NICHROME HEATING
element to provide multiple heat settings depending on
application requirements or available power. The heating
elements are operated by a 24VAC control circuit and a
number of relays and contactors. For safety, there is an
air pressure switch that will shut the heating elements off
OR PREVENT THE HEATING ELEMENTS FROM COMING ON IF AIRmOW
is restricted at either the inlet or the outlet. An additional
safety switch limits the incoming air temperature to
APPROXMIATELY & 4HIS SWITCH SHUTS OFF THE HEATING
elements and automatically resets when the temperature
FALLS TO APPROXIMATELY &
