compact
office
Theben AG
1103032101/09.07©Theben AG
Sensor module
compact office
Detection range:
horizontal
vertical
360°
120°
Recommended mounting height (Mh)
2.0 - 3.0m
Maximum range
6 x 6 m (H.mont. 2.5m)
8 x 8 m (H.mont. 3.5m)
Mixed light control
Light measurement deactivated
ca. 10 - 1500Lux
„on“
Switch off delay for light
Short pulse
10sec. - 20min.
0.5sec. „on“/ 10sec. „off“
Switch off delay for presence
10sec. - 120min.
Switch on delay for presence
Room surveillance
0sec. - 10min.
Power module
compact power
Mains voltage
230V ±10%, 50Hz
Relay output A for light
Relais, 230V
Nominal voltage
230V ±10%
Max. switching capacity:
incandescent lamps, halogen
1400VA
1200W
Max. number of electronic ballasts *)
A relay or contactor must be connec-ted in
case of more powerful devices
10x (1x58W); 5x (2x58W)
16x (1x36W); 8x (2x36W)
16x (< 36W)
Relay output B for presence
Relay potential-free
Maximum voltage
220V DC / 250V AC
Maximum switching capacity
50W / 50VA
Recommended minimum load
0.5mV / 10mA
Depth
Diameter
Mounting plate
40mm
48mm
70 x 70mm
Screw-Terminals
max. 2x 2.5mm
2
Size of concealed housing
(for flush-mounting)
Dim. 1, (NIS,PMI)
Ambient temperature
0° - 50°C
Degree of protection
IP 40
Article numbers
compact office complete
201 0 000
• Sensor module compact office
• Power module compact power
Surface frame for compact office
907 0 514
Service remote control QuickSet plus
907 0 532
User remote control clic
907 0 515
Settings on the Compact Office
(see figure above)
Brightness threshold (Lux)
Switch off delay for light/ activation of pulse function
Switch off delay for presence (HVAC/surveillance)
Switch on delay for HVAC/
activation of room surveillance function
DIP switches
:
DIP1
Lighting control: fully/semi-automatic
DIP2
Push button function: Room/Corridor
DIP3
Push button/switch control
DIP6
Operation mode: normal operation/test
Mechanical safety lock
The mechanical lock serves to secure the sensor
module firmly on the power module.
*) Use of T5-FL: When using T5-FL lamps with a comparable watta-
ge, the same number of electronic ballasts may be connected to the
detector’s switching contact as for the T8-FL. When using the 80W-
FL, the number should be halved in comparison to the 58W-FL.
Technical Specifications for Presence Detector compact office
Sensor Module - Rear Side
Accessories
QuickSet plus Service Remote Control
For the start-up procedure, the QuickSet plus service re-
mote control is available for the installation personnel or
the technical service. It allows convenient remote adjuste-
ment of all potentiometer values. Manual adjustement of
the potentiometers directly on the device remains possible
at all times.
Clic User Remote Control
The clic user remote control is available for the user
enabling product-spreading, individual switching of up
to two lighting groups. The user can choose between two
programmable scenes. Adjoining groups can be demarca-
ted from each other.
Surface Frame
A suitable frame for surface mounting is also available.
Declaration of CE conformity
This device complies with the protection regulations of the EMC direc-
tives 89/336/EEC, of the Low Voltage directive 73/23/EEC and of the
amending directives 92/31/EEC and 93/68/EEC.
SYSTEMS FOR TIME, LIGHT, CLIMATE
