THE STANDING DESK THE ÄNDERN MOTOR Скачать руководство пользователя страница 5

Страница: 5 / 8

FOR VIDEO INSTALL INSTRUCTIONS GO TO TheStandingDesk.com/install

THE ÄNDERN MOTOR

MONO COLUMN ELECTRIC TABLE

ASSEMBLY INSTRUCTIONS

STANDING

THE

DESK

• Run the Handset & Motor

Cables together and coil them.

• Using the 1/2” Wood Screws,

attach the 7/8” Cable Clips to
the worksurface to secure the
coiled Cables’ positions.

• Slip the 5/16” Cable Clips

over the uncoiled Cables at
preferred placement and secure
with the 1/2” Wood Screws into
the pilot holes.

• Plug the Motor Cable into the

Column Cable.

• Attach the handset

to the worksurface
with the 1/2” Wood
Screws and a Phillips
Head Screwdriver.

(SEE REFERENCE
GUIDE ON p. 8)

• Plug the Handset

Cable and Motor
Cable into the
Control Box.

1/2” Wood

Screw (5)

#2 Phillips Head

Screwdriver

1/2” Wood

Screw (2)

#2 Phillips Head

Screwdriver

NOTE: Motor Cable

MUST be plugged

into Motor Group

1 (M1) on Control

Box.

NOTE: Cable Clip positions are

USER DEFINED.

7/8” Cable

Clips (2

)

5/16” Cable Clip (3)

Содержание THE ÄNDERN MOTOR









Результаты поиска

Содержание THE ÄNDERN MOTOR

Отзывы:

Бренды по названию

Популярные бренды

THE STANDING DESK THE ÄNDERN MOTOR, Руководство по сборке

Результаты поиска

Содержание THE ÄNDERN MOTOR

Отзывы:

Бренды по названию

Популярные бренды