THE STANDING DESK THE ÄNDERN MOTOR Скачать руководство пользователя страница 1

Страница: 1 / 8

FOR VIDEO INSTALL INSTRUCTIONS GO TO TheStandingDesk.com/install

THE ÄNDERN MOTOR

MONO COLUMN ELECTRIC TABLE

ASSEMBLY INSTRUCTIONS

STANDING

THE

DESK

Article #: 929 011 369 0000

INCLUDED HARDWARE PACKAGE

INCLUDED TOOLS

PLEASE REVIEW

these instructions completely

and verify all parts are included in this package

before beginning assembly. Do not discard

the packaging until satisfied that the product

operates properly. Assembly and operation

of this desk must be in accordance with these

assembly instructions to avoid the risk of injury.

Keep these Assembly and Operation Instructions

near the assembly for reference.

REQUIRED TOOLS

5/16” Cable Clip (3)

Glides (4)

Socket Head

Cap Screw (4)

Flat Head

Cap Screw (4)

1/2” Wood

Screw (7)

1” Wood

Screw (4)

Allen Wrench

#2 Phillips Head

Screwdriver

1/2” Wrench

NOTE: Maximum lift capacity for the

ndern Motor desk is 175 lbs.

The table support is

solely intended to serve the purpose of ergonomic adjustments for your desk in accordance with

the weights and measurements given in these instructions. Any usage other than that mentioned

in this document is inappropriate; the manufacturer disclaims liability for any resulting damages. In

such cases the user bears the full risk. The manufacturer cannot be held responsible for any losses

or damages resulting from unauthorized modifications of this desk.

7/8” Cable

Clips (2

)

INCLUDED CORDS AND

COMPONENTS

9/16” Wood

Screw (3)

Motor Control

Box (1)

3m Power Cord (1)

Motor Extension

Cable (1)

Control Handset (1)

SCAN

FOR

ASSEMBLY

VIDEOS

Содержание THE ÄNDERN MOTOR









Результаты поиска

Содержание THE ÄNDERN MOTOR

Отзывы:

Бренды по названию

Популярные бренды

THE STANDING DESK THE ÄNDERN MOTOR, Руководство по сборке

Результаты поиска

Содержание THE ÄNDERN MOTOR

Отзывы:

Бренды по названию

Популярные бренды