background image

 

 

 

IMPORTANT SAFETY WARNINGS 

 

TO REDUCE RISK OF INJURY: Before any use be sure everyone using this product reads and understands all 

safety instructions and other information contained in this manual. 

GENERAL SAFETY 
STAY ALERT  

  

Do not operate the machine while under the influence of drugs, alcohol, or any medication that could affect 
your ability to use it properly. Do not use this machine when you are tired or distracted from the job at hand. 
Be aware of what you are doing at all times. Use common sense. 

USERS 

Do not at any time carry passengers sit or stand on the machine. Do not allow children to play on, stand upon 
or climb in the machine. Never allow children or people unfamiliar with these instructions to use the machine. 
Local regulations can restrict the age of the operator. 

AVOID DANGEROUS CONDITIONS   

Work in daylight or in good artificial light; always be sure of your footing on slopes; walk, never run with the 
machine; exercise extreme caution when changing direction on slopes; do not work on excessively steep 
slopes; use extreme caution when reversing or pulling the machine towards you; do not put hands or feet near 
or under rotating or moving parts. 

KEEP BYSTANDERS AND CHILDREN AWAY    

Keep unauthorised persons a safe distance away from the machine. If approached, stop the machine 
immediately. Do not allow children to handle, climb on or use the machine. Keep in mind the operator or user 
is responsible for accidents or hazards occurring to other people or their property. 

INSPECT YOUR MACHINE    

Check all bolts, nuts, and screws for tightness before each use, especially those securing guards and drive 
mechanisms. Vibration during use, may cause these to loosen. 
Form a habit of checking to see that all other tools/equipment are removed from the working area before 
turning it on. Replace damaged, missing or failed parts before using it. Warning labels carry important 
information. Replace any missing or damaged warning labels. 

DRESS PROPERLY 

Do not wear loose clothing, gloves, scarfs, neckties or jewellery (rings, wrist watches), which can be caught in 
moving parts. Always wear long trousers. Always wear substantial non slip, substantial or heavy-duty safety 
footwear are highly recommended when working. Never operate barefoot or when wearing sandals. Wear a 
face or dust mask if the operation is dusty. Always wear safety glasses/goggles and/or face shields. Everyday 
eyeglasses have only impact resistant lenses; they are not safety glasses/goggles. Wear protective hair 
covering to contain long hair, preventing it from getting caught in machinery.  

DO NOT OVERREACH 

Keep proper footing and balance at all times when using the machine. Use on slopes with great care. Never 
stand on the machine. Serious injury could occur if the machine is tipped or if the moving parts are 
unintentionally contacted. Do not store anything above or near the machine, where anyone might stand on 
the machine to reach them. 

AVOID INJURY FROM UNEXPECTED ACCIDENT  

 

Keep hands & feet out of the way of all moving parts. Do not place any part of your body or any tool e.g. in the 
machine during operation.  

DO NOT FORCE TOOL  

 

Always work within the rated capacity. Do not use machine for a purpose for which it was not intended. Before 
operating vehicle on any grade (hill) refer to the safety rules in the vehicle owner

s manual concerning safe 

operation on slopes. 

Stay off steep slopes! 

Always operate at reduce speed in rough terrain, along creeks, 

ditches and on hillsides. Do not operate close to creeks, ditches and public highways. To avoid personal injury 
and/or equipment damage 

DO NOT EXCEED 5 MPH

. Always use caution when loading and unloading the cart. 

Only tow with recommended vehicles (Lawn/Garden Tractors and ATVs). Always secure and lock dump cart to 
the vehicle hitch before operating.  

NEVER LEAVE MACHINE RUNNING UNATTENDED    

Do not leave the machine unattended until it has come to a complete stop. 

TYRE INFLATION 

Tyre pressures must always be inspected prior to each use. Do not over inflate and always use a manual foot 

Содержание THTS175

























Отзывы: