The Handy 1938115002 Скачать руководство пользователя | Manualshive

Страница: 8 / 20

background image

STEP 2



Attach the Wheel Assembly Frame to each side of the Gearbox Assembly and Fixing Connecting
Rod, insert two bolts M6x35 into the fixing connecting rod through the Wheel Assembly Frame.



Make sure the hole in the Gearbox Axle is on the RIGHT SIDE, when assembling, as shown.



Attach the Wheel Assembly Frames & Support Leg onto the Hopper using bolts M6x70, M6 Lock
Nuts and Large Flat Washers Ø6.

NOTE: WE ADVISE YOU DO NOT TIGHTEN THE NUTS & BOLTS COMPLETELY AT THIS POINT.

Big Flat Washer Ø6

Bolt
M6x35

Bolt M6x35

Connect the two wheel
frames to the axle using
M6x35 bolts

«
...
6
7
8
9
10
...
»

Содержание 1938115002





















Отзывы:

Нет отзывов

Похожие инструкции для 1938115002

Бренд: Magtek Страницы: 18

Бренд: Farpointe Data Страницы: 2

Bulk Pro SP-1575

Бренд: SnowEx Страницы: 24

Бренд: SAMSys Страницы: 60

FLEX-SELECT F130 Series

Бренд: EarthWay Страницы: 14

FlashMover 23-in-1 USB2.0

Бренд: Microdia Страницы: 2

MULTI-CARD 24-IN-1 READER

Бренд: Lexar Страницы: 10

Бренд: TURFMASTER Страницы: 3

Бренд: TurfEx Страницы: 24

Бренд: abi Страницы: 17

Бренд: Diablotek Страницы: 1

Бренд: Vivotech Страницы: 2

Бренд: G4S Страницы: 2

Бренд: G4S Страницы: 2

Бренд: StarTech.com Страницы: 2

Бренд: GIGA-TMS Страницы: 22

Бренд: WAYFARER Страницы: 13

Бренд: Yard Tuff Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды