Once the unit has been fully assembled and filled with water you are ready to turn the unit on.
Turning the unit ON:
1. Plug the Power Cord into an electrical outlet. The Red Power Indicator light will come on, indicating power is on.
At the same time the Blue Water Tank Light will come on.
2. Wait for approximately 15 to 25 seconds for the Steam Power Level Indicator lights to flash, indicating that the unit
is ready to use.
3. Press the Steam Switch to begin emitting steam.
4. Press the Steam Setting Button to your desired power level; for Low Steam, press the button once, two times for
Medium Steam and three times for High Steam. Pressing the button again will bring you back to the Low Steam setting.
5. To stop emitting steam, press and hold the Steam Switch for approximately 5 to 6 seconds. While holding the Steam Switch the Steam
Power Level Indicator lights will flash. Steam will not stop emitting until the flashing stops and a beep noise is heard indicating it has
been stopped.
6. The unit is still on, and another press of the Steam Switch will start the emission of steam.
Turning the unit OFF:
1. To shut the power off to the unit, follow the instructions to turn the steam off (see above), and then unplug the Power Cord from the Electrical Outlet.
When trying to stop Steam Emission, failure to hold the button long enough to stop flashing lights and hear the
beep, will cause the unit will to continue steaming at the last steam setting.
How to use your H2O™ HD
1. Low Steam – Blue Indicator Light
Ideal for sensitive surfaces such as Sealed
Hardwood/Laminate (may also use Medium
Steam setting), Garments, Mattresses &
Pillows, and Upholstery
2. Medium Steam – Green Indicator Light
Ideal for light cleaning of Plastic, Granite &
Marble, Tile, Slate and Windows & Mirrors
3. High Steam – Red Indicator Light
Ideal for tougher stains on Stainless Steel,
Porcelain Fixtures and Carpets & Door Mats
Select one of the Steam Power Level positions:
Steam Switch
with
Power Indicator Light
To fill the Water Tank:
Ensure the H2O™ HD Steam Cleaner is unplugged. Remove the Water Tank by pressing the Water Tank Release Button and pulling the
Water Tank from both sides (Fig. 1). Turn the Water Tank Cap from the bottom of the Water Tank to “OPEN” and remove the Water
Tank Cap (Fig. 2). Fill the Water Tank to the indicated tank capacity (450ml/15.2oz) (Fig. 3). Replace the Water Tank Cap and turn to
“CLOSE” position. Make sure the Copper Cone inside the Water Tank is always submerged in water while operating the unit.
Never put cleaning detergents into the Water Tank. Unless approved by the manufacturer, do not put any scented products in the Water Tank.
The H2O™ HD Steam Cleaner uses tap water, but in areas with hard water use distilled water for better performance.
Fig. 1
Fig. 2
Fig. 3
The H2O™ HD Steam Cleaner is designed to thoroughly clean floor surfaces, such as marble, ceramic, carpet, stone, linoleum, sealed
hardwood floors and parquet. Test the H2O™ HD Steam Cleaner on a small isolated area of your floor prior to overall use on floor surfaces.
The heat and steam action may remove the wax on surfaces treated with wax. Do not let unit stand on any wood or heat-sensitive floors for
an extended period of time. Water marks, discoloration or damage to the floor surface can occur if the unit is left operating too long in one
place. When using on vinyl, linoleum or any other heat-sensitive floors, use extra caution. Too much heat can melt glue in the flooring. Use
only on laminate flooring that has been laid professionally and without gaps or cracks that would permit the entry of moisture. Not all floor
types are suitable for steam cleaning. Always check the use and care instructions of your flooring manufacturer or distributor before using
the H2O™ HD Steam Cleaner. When in doubt consult a flooring specialist.
Start Cleaning:
Slowly pass over the surface to be cleaned. The absorbent mop cloth picks up the dirt loosened by the steam. Apply steam as needed.
When the H2O™ HD Steam Cleaner stops producing steam, simply turn it off, unplug it from the electrical outlet and refill the Water Tank
to continue cleaning.
Never leave the H2O™ HD Steam Cleaner unattended while plugged in.
For Best Results:
1. Sweep or vacuum floor prior to using the H2O™ HD Steam Cleaner.
2. To avoid puddling of water, the Microfiber Cloth must be clean and dry for use. To replace the cloth, proceed as follows: Let the cloth cool
down, remove cloth from unit, replace with a new Microfiber Cloth (optional item) and continue use. Select Low Steam power level.
3. To help sanitize an area of your floor, leave the H2O™ HD Steam Cleaner at a High Steam power level over the area for about 10
seconds, but no longer than 15 seconds.
Do not carry out this procedure on heat and steam sensitive floors.
• Never steam on one spot for too long. This can cause floor surface damage.
• Do not put hands or feet under the steam mop. Unit gets very hot.
• During use a pulsing noise may be heard indicating that the mop is producing steam. This noise is normal.
• There may be some minor “spitting” of water mixed with the steam. This is also normal.
• The force and heat of the steam may adversely affect certain materials. Always check the suitability of using steam on a surface by carrying
out a preliminary test on a hidden area.
How to use your H2O™ HD
!
WARNING
!
WARNING
!
IMPORTANT
7
8
!
IMPORTANT
