88
Z-Max Surveying System Operation and Applications Manual
Warning Messages
The receiver monitors a number of conditions that are of interest to the user.
Whenever a problem is detected in one of these conditions, the LED display is
interrupted to show a warning message stating the problem. The warning message
scrolls across the display to distinguish it from a regular menu parameter, and a beep
will sound every 10 seconds (unless the beep has been disabled by the user). Press
any key to acknowledge the message, which removes the warning text from the
display and stops the beep. If the receiver is experiencing more that one problem at
the same time, the receiver will generate a separate warning for each problem. In this
case, the receiver will display the highest priority warning first. When this warning is
acknowledged, it will display the next highest priority warning. This process will
continue until all warnings have been acknowledged. Table 4.6 describes the possible
warnings the receiver may issue.
Table 4.6.
Warning Messages
Warning
Definition
Action
THALES RADIO WARNINGS
Wrong setting
A conflict in one of the parameters
is preventing radio programming.
Check and reset radio parameters.
Communication Error
A timeout or checksum error has
occurred during setup or user is
trying to power off an external
device by front panel menu.
Recheck the port and baud rate
parameters.
Not Loaded Yet
The LOAD function was not per-
formed prior to programming user
parameters.
Load radio parameters (LOAD) sub-
menu and then resend the user
parameters (PROGRAM) submenu.
PDL RADIO WARNINGS
Channel Not Programmed
The frequency channel selected
is not programmed in the channel
table.
Reload (LOAD) radio parameters.
Wrong setting
A conflict in one of the parameters
is preventing radio programming.
Check and reset radio parameters.
Communication Error
A timeout or checksum error has
occurred during setup, or the
external radio has been powered
off.
Recheck the port and baud rate
parameters .If using an external
radio, verify it is powered up.
Not Loaded Yet
The LOAD function was not per-
formed prior to programming user
parameters.
Load radio parameters (LOAD) sub-
menu and then resend the user
parameters (PROGRAM) submenu.
G3.book Page 88 Saturday, May 24, 2003 12:52 PM
Содержание Z-Max
