TFortis PSW-2G4F-Box Скачать руководство пользователя | Manualshive

Страница: 16 / 30

background image

16

3.7 Integrated lightning protection

PSW-2G4F-Box switch has built-in lightning protection modules that protect
Ethernet ports and ~230VAC power circuits from common-mode and differential

electromagnetic interferences.
The switches are resistant to powerful microsecond pulse interferences

according to GOST R 51317.4.5 standard as per Table 3.7.1 with performance
criteria B (temporary disruption of performance or functioning with further
recovery without operator's intervention).

Table 3.7.1

Port

Pulse

2 kV

4 kV

2 kV

IMPORTANT!

Grounding of the switch is mandatory for lightning protection.

3.8 DIN rail and automatic circuit breaker

A 35 mm DIN rail is provided inside the switch to allow installation of additional

equipment.

«
...
14
15
16
17
18
...
»

Содержание PSW-2G4F-Box































Отзывы:

Нет отзывов

Похожие инструкции для PSW-2G4F-Box

TotalStorage 3534-F08

Бренд: IBM Страницы: 105

RedBooks SAN24B-5

Бренд: IBM Страницы: 11

RedBooks SAN24B-5

Бренд: IBM Страницы: 2

Бренд: IBM Страницы: 123

8265 Nways ATM Switch

Бренд: IBM Страницы: 192

TRIPP LITE Series

Бренд: Eaton Страницы: 8

Бренд: National Instruments Страницы: 23

Бренд: Gefen Страницы: 31

Бренд: ORiNG Страницы: 2

TIMEGUARD WF10COM

Бренд: Theben Страницы: 35

Elinx EIR418-2SFP-T

Бренд: B&B Electronics Страницы: 25

Бренд: CIS Страницы: 3

Бренд: Watchguard Страницы: 26

Бренд: Advantech Страницы: 101

pro-trim PT1000

Бренд: Seastar Solutions Страницы: 2

Бренд: WTI Страницы: 56

Бренд: H3C Страницы: 3

Бренд: TE Connectivity Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды