WeatherHub Sensor
This sensor is a component of the „WeatherHub“ system for measuring air temperature and humidity (indoor or
outdoor) and water temperature, it can be used with this system only. To use the sensor you need an installed
WeatherHub gateway.
Before you use it:
Please be sure to read this short-instruction manual carefully.
Following the instruction manual for use will prevent damage to the device and loss of your statutory rights arising
from defects due to incorrect use.
We shall not be liable for any damage occurring as a result of not following these instructions. Likewise, we take no
responsibility for any incorrect readings and for any consequences which may result from them.
Please take particular note of the safety advice!
Please look after this manual for future reference.
For your safety:
•
The product is exclusively intended for the field of application described above. The product should only be
used as described within these instructions.
•
Unauthorised repairs, modifications or changes to the product are prohibited.
Caution!
Risk of injury:
•
Keep this instrument and the batteries out of reach of children.
•
Batteries must not be thrown into the fire, short-circuited, taken apart or recharged. Risk of explosion!
•
Batteries contain harmful acids. Low batteries should be changed as soon as possible to prevent damage
caused by a leaking battery. Never use a combination of old and new batteries together or batteries of
different types.
•
Remove the batteries if you do not use the product for a lengthy period.
•
Wear chemical-resistant protective gloves and glasses when handling leaked batteries.
Important information on product safety!
•
Do not place your device near extreme temperatures, vibrations or shocks.
•
Clean the instrument with a soft damp cloth. Do not use solvents or scouring agents.
Sensor set up
•
Open the battery cover of the thermo-hygro sensor.
•
Hold the body of the pool sensor and unlock the upper part by turning it counter clockwise and separate it
carefully from the body.
•
First, insert 2 x 1,5 V AA batteries in the thermo-hygro sensor.
•
Then insert 2 x 1,5 V AA batteries in the pool sensor. Observe the correct polarity (see marking).
•
Close the battery cover of the thermo-hygro sensor and screw the two parts of the pool sensor together
again. Ensure that the cover is flat and sufficiently tight secured (markings should correspond). This will
prevent water from entering the battery compartment and subsequently damage the unit.
•
In order to ensure sufficient transmission however, the distance between the thermo-hygro sensor and the
gateway should not be more than 100 meters and 25 meters to the pool sensor (in water).
Application
Placed outside, choose a shady and dry position for the thermo-hygro sensor. Direct sunshine falsifies the measure-
ment and continuous humidity strains the electronic components needlessly. The thermo-hygro sensor is used to
control temperature and humidity in the indoor or outdoor area, the pool sensor measures the water temperature in
the swimming pool, whirlpool or pond.
Add sensor
Open the app, dashboard is displayed. Tap „Add new sensor“ and scan the QR code on the back of the sensor. A
copy of the sensor code is attached. Then set a name for the sensor
.
Battery replacement
The battery status of the thermo-hygro sensor will be shown by the WeatherHub app.
Replace the batteries of the pool sensor when the battery symbol appears in the display of the pool sensor.
Please note: When the batteries are changed, the contact between thermo-hygro sensor and pool
sensor must be restored – so always restart both devices.
Specifications
Batteries thermo-hygro sensor:
2 x mignon (LR06, AA)
Batteries pool sensor:
2 x mignon (LR06, AA)
Measuring range temperautre:
– 39,9°C … +59,9°C (-39,8 … 139,8°F)
Measuring range humidity:
0% … 99% rH
Accuracy temperature:
+/- 1°C (0 ... 50°C) rest 2,5°C
Accuracy humidity:
+/- 3% (from 20% ... 80% rH) rest +/- 5%
Measuring range pool sensor:
0°C ... 60°C (32 ... 140°F)
Measuring interval:
30 seconds
Transmitting interval:
7 minutes
Frequency thermo-hygro sensor:
868,3 Mhz
Transmitting range pool to transmitter: 25m (free field)
Transmitting range to Gateway:
100m (free field)
Maximum radio-frequency power:
< 25mW
Do not dispose of batteries or rechargeable batteries in the household waste!
As a consumer, you are legally required to take them to your retail store or to appropriate
collection sites according to national or local regulations in order to protect the environment.
The symbols for the heavy metals contained are: Cd=cadmium, Hg=mercury, Pb=lead
This instrument is labelled in accordance with the EU Waste Electrical and Electronic Equipment
Directive (WEEE). Please do not dispose of this product with other household waste. The user is
obligated to take end-of-life devices to a designated collection point for the disposal of
electrical and electronic equipment, in order to ensure environmentally-compatible disposal.
More information and detailed instructions can be found in the app at “Info” or on
www.tfa-dostmann.de/weatherhub.
TFA Dostmann GmbH & Co. KG, Zum Ottersberg 12,
D-97877 Wertheim, www.tfa-dostmann.de
Quick reference
30.3310.02 Thermo-Hygro sensor
and pool sensor
Waste disposal
This product has been manufactured using high-grade materials and components which can be recycled
and reused.
EU Declaration of conformity
Hereby, TFA Dostmann declares that the radio equipment type 30.3310.02 is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
www.tfa-dostmann.de, E-Mail: [email protected]
TFA Dostmann GmbH & Co.KG, Zum Ottersberg 12, D-97877 Wertheim, Germany
No part of this manual may be reproduced without written consent of TFA Dostmann.
The technical data are correct at the time of going to print and may change without prior notice.
The latest technical data and information about your product can be found by entering
your product number on our homepage.