Textron Jacobsen HR-5111 Скачать руководство пользователя страница 227

Страница: 227 / 423

HYDROSTATIC POWER TRAIN

4203780 First Edition

5-63

Figure 5-66

WARNING

22. Raise the mower so wheels are off the ground. Place

jackstands under the frame to support the mower.

23. Support the axle assembly using a suitable lifting

device.

24. Remove two nuts (51), lock washers (50), and

screws (63), and four flat washers (49 and 64).

25. Remove two screws (45), lock washers (46) and flat

washers (65), and remove scraper (47).

26. Remove right lift arm support (48) from frame.

27. Remove two nuts (55), lock washers (54), and

screws (60), and four flat washers (53 and 61).

28. Remove two screws (58), lock washers (57) and flat

washers (56), and remove scraper (59).

29. Remove left lift arm support (52) from frame.

Figure 5-67

30. Remove four screws (67) and lock washers (66), and

remove front axle assembly (68) from the frame.

Installation Notes

• Install the front axle by reversing the order of

removal.

• Bleed the brake system. (See “Bleed Brake System”

on page 9-5.)

• Pressure filter traction system upon start-up if metal

debris is found in system oil. (See “Portable In-Line
Filter” on page 5-4.)

• Check hydraulic oil level. Add oil as needed. (Refer to

“Safety, Operation, and Maintenance Manual” for the
correct oil specifications.)

• Support the machine using properly rated

jackstands. Never work under a machine
supported only by a jack.

• Do not use wood or concrete blocks to

support the machine. Failure to properly
support the machine may result in death or
serious injury.

TN2054

TN2056

Содержание Jacobsen HR-5111








































































































































































































































































































































































































































Результаты поиска

Содержание Jacobsen HR-5111

Отзывы:

Похожие инструкции для Jacobsen HR-5111

Бренды по названию

Популярные бренды

Textron Jacobsen HR-5111, Техническое руководство по ремонту

Результаты поиска

Содержание Jacobsen HR-5111

Отзывы:

Похожие инструкции для Jacobsen HR-5111

Бренды по названию

Популярные бренды